background image

WASP Line Array User Manual rev 2.00

5

 

                                           in

fo@mag-audio

.c

om

Tel./F

ax:

 +

38 044 277

-4

7-89

 

www

.mag-audio.com

1. Safety instructions

1. Read these instructions carefully.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance 

with the manufacturer’s instructions.

8. Do not use near heat sources such as stoves, heat registers, 

radiatiors or other equipment (including amplifiers) that 

produces heat.

9. Do not use the unit near open fire sources.

10. Connect the unit only to the electric network with grounding. 

Use only electic plugs that provide grounding.

11. Protect the power cord from being walked on, pinched, or 

otherwise damaged.

12. Use only accessories specified by the manufacturer.

13. Unplug this unit during lightning storms or when unused for 

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is 

required when the system has been damaged in any way, such 

as power supply cord or plug is damaged, liquid has been spilled 

or objects have fallen into the unit, the unit has been exposed 

to rain or moisture, does not operate normally, or has been 

dropped.

15. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC 

SHOCK, DO NOT EXPOSE THIS SYSTEM UNIT TO RAIN OR 

MOISTURE.

THIS UNIT CONTAINS POTENTIALLY LETHAL VOLTAGES. 

TO PREVENT ELECTRIC SHOCK OR HAZARD, DO NOT 

REMOVE THE AMPLIFIER MODULE. NO USER SERVICEABLE 

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL. 

1

INSTALLING OF THIS UNIT MUST BE PERFORMED ONLY BY 

QUALIFIED TRAINED PERSONNEL FOLLOWING APPLICABLE 

SAFETY RULES. DO NOT ALLOW INSTALLATION OF THIS UNIT 

IF INSTALLATION HARDWARE IS BROKEN, BENT, PARTS ARE 

MISSING OR IS OTHERWISE DAMAGED.

- for powered speakers only

The triangle with the lightning bolt is used to alert the 

user to the risk of electric shock.

The triangle with the exclamation point is used to 

alert the user to important operating or maintenance 

instructions.

The CE-mark indicates the compliance with the low 

voltage and electromagnetic compatibility.

Symbol for earth/ground connection.

Symbol indicating that the equipment is for indoor use 

only.

Symbol for conformity with Directive 2002/96/EC and 

Directive 2003/108/EC of the European Parliament on 

waste electrical and electronic equipment (WEEE).

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, 

DO NOT ATTEMPT TO OPEN ANY PART OF THE 

UNIT. NO USER-SERVICEABLE PARTS INSIDE. REFER 

SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO COMPLETELY DISCONNECT THIS APPARATUS 

FROM THE AC MAINS, DISCONNECT THE POWER 

SUPPLY CORD PLUG FROM THE AC RECEPTACLE.

THE MAINS PLUG OF THE POWER SUPPLY CORD 

MUST REMAIN READILY ACCESSIBLE.

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR 

MOISTURE, DRIPPING OR SPLASHING LIQUIDS. 

OBJECTS FILLED WITH LIQUIDES, SUCH AS VASES, 

SHOULD NOT BE PLACED ON THIS APPARATUS.

CONNECTIONS TO THE MAINS SHALL BE DONE ONLY 

BY AN ELECTROTECHNICALLY SKILLED PERSON 

ACCORDING TO THE NATIONAL REQUIREMENTS OF 

THE COUNTRIES WHERE THE UNIT IS SOLD.

EXPLANATIONS OF GRAPHICAL SYMBOLS

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Summary of Contents for WASP Series





















Reviews: