background image

 
 

 

   P.15                                  Maestro M110 Series

                          

www.maestro-wireless.com

 

 

 

7.4  

Network Registration 

 

To verify network registration, first ensure the SIM card has been provisioned. 

 

If the model has embedded SIM, first ensure the modem has been activated 
by the network provider. 

 

To see the network registration status, in terminal program, enter: 
 

AT+CREG? 

 
and refer to the below responses of network registration status; 
 
 

Response  

Description 

+CREG: 0,0 

Not registered 

+CREG: 0,1 

Registered on home network 

+CREG: 0,2 

Not registered and attempting  

+CREG: 0,5 

Registered on network when roaming 

 

 

If it is not registered on the network, check the following;

 

 

  If the antenna was attached properly 

  The received signal strength (refer to section 8.2) 

  If the SIM card was provisioned 

 
 
7.5 

PIN Code 

 

To verify, in terminal program, enter: 
 

AT+CPIN?  

 
and refer to the below responses of PIN code status; 
 
 

Response  

Description 

+CPIN: READY 

PIN code has been entered correctly or not required 

+CPIN: SIM PIN 

PIN code has not been entered or entered incorrectly  

 

 

Summary of Contents for M110 Series




















Reviews: