manualshive.com logo in svg

Madill 3000, Operation & Maintenance Manual

Share
Download
Madill 3000 Operation & Maintenance Manual Download Page 35

 
 

32 

Fuel Tank 

Fill the tank daily or as required with diesel fuel. Location of the filler cap is on the top 
of  the  tank  at  the  rear  of  the  upper  grated  platform.  Ensure  adequate  fuel  level  is 
maintained. 

Hydraulic Oil Tank 

Check this daily for oil level. A sight glass is provided and located on the side of the 
hydraulic  tank.  Clean  hydraulic  oil  should  be  added  via  the  hand  pump  and  wand 
assembly on the side of the hydraulic tank. Never overfill the system. 

Never run the 

machine with low oil because this may damage the pumps

. 

Urea (DEF) Tank 

Top  up  the  DEF  tank  with  every  fuel  fill;  only  use  AddBlue/DEF  meeting  ISO-22241 
specification. Store DEF out of direct sunlight where temperatures 

Do NOT

 exceed 35 

deg.  C.  DEF  is  very  corrosive,  contact  with  the  solution  can  cause  irritation.  When 
handling wear gloves, change gloves and clothes if spillage occurs.  

Note:

 Upon engine shut down DEF pump will evacuate fluid out of system to prevent 

freezing and solution spoiling. 

Do NOT

 disconnect power before the completion of this 

process which can take up to 2 minutes (see Night Switch Operation). 

Engine Crankcase 

Check the level of the engine oil daily and add the proper oil as necessary (see the 
manufacturer

’s recommendations). 

Never operate the engine with low oil. 

Change 

the oil filter at every oil change. 

Radiator 

Check the coolant level daily. Be sure to use the appropriate coolant mixture in cold 
weather.  Consult  the  engine  manufacturer

’s  recommendations.  Change  the  coolant 

and flush the system as per lubrication & maintenance chart. Keep the radiator and oil 
cooler  fins  clean  so  that  the  cooling  system  may  operate  efficiently.  Refer  to  the 
engine manufacturer

’s manual for specific information on engine coolant and service. 

Batteries 

Check the water level of both batteries weekly. If it is necessary to fill the battery, use 
distilled water only. 

DO NOT USE TAP WATER 

as it may contain minerals which will 

contaminate the electrolyte

. 

Batteries are located on the floor in the cab riser. 

 

 

Summary of Contents for 3000













































Reviews:

No comments

Brands by name

Popular brands

Load more brands