manualshive.com logo in svg

MadgeTech RTDTemp2000, Manual, Page: 35 / 38

Share
Download
MadgeTech RTDTemp2000 Manual Download Page 35

Page 34

MadgeTech  RTDTemp2000

Section 9:  Maintenance

Section 9:  Maintenance

The RTDTemp2000 does not have any user-serviceable parts except the 
battery which should be replaced periodically. The battery life is affected by 
battery type, ambient temperature, sample rate, sensor selection, offl oads 
and LCD display usage. The RTDTemp2000 has a battery status indicator on 
the LCD display. If the battery indication is low, or if the device seems to be 
inoperable, it is recommended that the battery be changed.

To change the battery, locate and remove the four (4) 3/32 hex screws on 
the back of the unit. Separate the halves and the battery compartment is 
now visible. Remove the old 9V battery from the battery clips and replace 
with a new 9V battery. MadgeTech recommends using 9V lithium battery. An 
alkaline battery is acceptable, but will yield a shorter battery life.

For any other maintenance or calibration issues, MadgeTech recommends 
the unit be returned to the factory for service. Before returning the device, 
you must obtain an RMA from the factory.  For further information, please 
contact MadgeTech at:

MadgeTech, Inc

.

PO Box 50

201 Route 103 West

Warner, NH 03278

TEL: 603-456-2011 

•

 FAX: 603-456-2012

[email protected]

www.MadgeTech.com

  BATTERY WARNING

  Most MadgeTech data loggers contain a lithium battery. Do    
  not cut the battery open, incinerate, or recharge. Do not heat   
  lithium batteries above the specifi ed operating temperature.*  
  Dispose of the battery in accordance with local regulations.

  
  *See the individual specifi cation sheets at www.madgetech.com.

Summary of Contents for RTDTemp2000







































Reviews:

No comments