Macurco DMK-1 Installation Manual Download Page 12

DMK-1 Installation Guide 

REV 

 1.0 

[34-2900-0065-9 ] 

12 

|

 

P a g e

 

6

 

Macurco Gas Detection Product limited warranty 

Macurco warrants the DMK-1 Duct Mount Kit will be free from defective materials and workmanship for a period of two (2) years 
from the date of manufacture, provided it is maintained and used in accordance with Macurco instructions and/or 
recommendations. If any component becomes defective during the warranty period, it will be replaced or repaired free of charge, if 
the unit is returned in accordance with the instructions below. This warranty does not apply to units that have been altered or had 

repair attempted, or that have been subjected to abuse, accidental or otherwise. The above warranty is in lieu of all other express 
warranties, obligations or liabilities. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR 
PURPOSE ARE LIMITED TO A PERIOD OF TWO (2) YEARS FROM THE PURCHASE DATE. Macurco shall not be liable for any 
incidental or consequential damages for breach of this or any other warranty, express or implied, arising out of or related to the use 
of said gas detector. The manufacturer 

or its agent’s liability shall be limited to replacement or repair as set forth above. Buyer’s 

sole and exclusive remedies are the return of the goods and repayment of the price, or repair and replacement of non-conforming 

goods or parts. 
 
 

Macurco Gas Detection 

3601 N. St. Paul Avenue 
Sioux Falls, SD 57104 
 

Technical Support Contact Information 

Phone:

 1-844-325-3050 

Fax:

 1-605-951-9616 

Email:

 

[email protected]

  

Website:

 

www.support.macurco.com

  

General Contact Information  

Phone :

 1-877-367-7891 

Fax :

 1-605-951-9616 

Email :

 

[email protected]

 

Website:

 

www.macurco.com 

          

 
 

REV 

 1.0 

Issue Date: 8-16-2019 
Document No: 34-2900-0065-9 

© Aerionics 2019. All rights reserved.  
Macurco is a trademark of Aerionics, Inc. 

 

 

 

 

 

 

 

 

 

Summary of Contents for DMK-1













Reviews: