6
HOOKUP DIAGRAMS
Quick Start
1. Start with the following settings on the back of the
SRM450v2:
Turn the POWER switch off (down).
Set the TIMED TURNOFF, CONTOUR, and LOW CUT
switches out.
WARNING:
Turn the LEVEL control
down (counterclockwise) before every
use. If not, you could be in for a startling
surprise, especially if the last time you
used it was with a microphone and now
you want to connect a line-level source.
2. Connect the output from your signal source (mixing
console, microphone, preamp, or other mic- or line-level
source) directly to the INPUT connector on the back of
the SRM450v2. It accepts balanced line-level signals from
mixers, preamplifiers, CD players, tape decks, etc., and
accepts direct connections from dynamic microphones.
3. Connect the supplied AC power cord to the IEC socket
on the back of the SRM450v2. Plug the other end into
an AC outlet properly configured with the correct
voltage for your particular model.
4. Turn on your signal source. Make sure its Master
Volume control (if it has one) is turned all the
way down.
5. Turn on the SRM450v2 POWER switch.
6. Start the signal source, whether it be speaking into a
microphone or starting a CD player. Adjust any volume
controls on the signal source for normal operation.
7. Slowly turn up the LEVEL control on the back of the
SRM450v2 until the desired volume is reached (and the
PEAK light does not come on)
Always
wear hearing
protectors if you are close when it is playing at high
levels.
8. If there is no sound,
always
turn down the SRM450v2
LEVEL control before investigating. There may be a
mixer or preamplifier mute or tape switch engaged,
or a mic switch off.
SRM450v2: STEREO OPERATION WITH A MIXER, AND USING THE THRU JACK
POWER
SIGNAL PRESENT
INPUT
THRU
THERMAL
PEAK
TIMED TURNOFF
ON
OFF
CONTOUR
LOW CUT
ON
75Hz
12k/AIR
100Hz
+3dB
MIC
LINE
LEVEL
(+4dBu)
NORMAL
+40dB
O
O
O
PARALLEL
POWER
SIGNAL PRESENT
INPUT
THRU
THERMAL
PEAK
TIMED TURNOFF
ON
OFF
CONTOUR
LOW CUT
ON
75Hz
12k/AIR
100Hz
+3dB
MIC
LINE
LEVEL
(+4dBu)
NORMAL
+40dB
O
O
O
PARALLEL
Mixing Console
(Mackie Onyx
1220i shown)
From Mixer
Left Output
From Mixer
Right Output
Thru
Mixing Console
(Mackie Onyx 1220i shown)
From Mixer
Right Output
From Mixer
Left Output
Thru
Next
Next
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MAIN MIX
TALKBACK
TAPE
MAIN OUT
IN
OUT
ALT 3-4 OUT
CTRL - RM OUT
EQ
MID
HIGH
L
L
L
L
R
R
R
R
R/4
L/3
L
R
L
R
1
2
3
4
EQ
MID
LOW
HIGH
EQ
MID
LOW
HIGH
MID
LOW
HIGH
HIGH
LOW
EQ
AUX
2
1
PAN
1
LINE
2
LINE
4
LINE
3
LINE
AUX MASTER
2
1
2
1
CTRL ROOM/PHONES
SOURCE
PHONES
CONTROL
ROOM
L
R
LOW
AUX
2
1
PAN
2
3
4
7-8
5-6
AUX
2
1
PAN
AUX
2
1
PAN
AUX
2
1
PAN
9-10
11-12
LINE IN 9-10
LINE IN 11-12
LINE IN 7-8
LINE IN 5-6
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
1
