Mackie SR1530Z User Manual Download Page 9

9

SR1530z SPECIFICATIONS

Acoustic Performance

 

Frequency Range (–10 dB) 

 

 

 

 

8 Hz–0 kHz 

 

Frequency Response (–3 dB)

 

 

 

 

 

50 Hz–18 kHz 

 

Horizonal Coverage Angle (–6 dB)

 

 

 

 

 

90º averaged  kHz to 10 kHz 

 

Vertical Coverage Angle (–6 dB)

 

 

 

 

 

40º averaged  kHz to 10 kHz 

 

Directivity Factor; DI (Q)

 

 

 

 

 

11. (1.) averaged k Hz to 10 kHz 

 

Max SPL long-term

 

1 dB @ 1m 

 

Max SPL peak 

16 dB @ 1m 

 

Crossover Points

 

700 Hz, 000 Hz

Input/Output

 

Input Type

   

Female XLR Balanced/Unbalanced 

 

Input Impedance

 

50 kohms balanced 

 

Loop-Through

 

Male XLR Balanced/Unbalanced 

 

 

 

 

(parallel with input)

High-Frequency Section

 

Voice Coil Diameter

  1.0 in/5 mm 

 

Horn Exit Diameter

  1.0 in/5 mm 

 

Phase Plug 

 

-slot optimized geometry 

 

Diaphragm Material

  Mylar 

 

Magnet Material

 

Ferrite

Mid-Frequency Section

 

Diameter

 

 

6.0 in/15 mm 

 

Phase Plug 

 

Optimized geometry 

 

Diaphragm Material

  Paper 

 

Magnet Material

 

Ferrite

Low-Frequency Section

 

Woofer Diameter

 

15.0 in/81 mm 

 

Voice Coil Diameter

  .5 in/6 mm 

 

Diaphragm Material

  Epoxy-reinforced cellulose 

 

Magnet Material

 

Ferrite

Power Amplifiers

Low-Frequency Power Amplifier

 

Rated Power 

 

00 watts rms 

 

Rated THD

   

< 0.0% 

 

Design 

 

Class G, Hybrid

Mid and High-Frequency Power Amplifiers

 

Rated Power 

 

100 watts rms 

 

Rated THD

   

< 0.0% 

 

Design 

 

Class AB

Line Input Power

 

US

  

 

 

10V, 60Hz 

 

 

Recommended Amperage Service: 

8 amps

 

Europe

 

 

0V, 50Hz 

 

 

Recommended Amperage Service: 

5 amps

 

AC Connector

 

-pin IEC 50 VAC

Safety Features

 

Input Protection

 

Low frequency dynamic bass  

 

 

 

 

protection, rms limiting, power  

 

 

 

 

supply and amplifier thermal  

 

 

 

 

protection

 

Display LEDs

 

Power ON, Protection

Construction Features

 

Basic Design 

 

Trapezoidal, 10º sides 

 

Material

 

 

18 mm multi-layered plywood,  

 

 

 

 

resin end caps 

 

Finish

 

 

Wear-resistant textured black  

 

 

 

 

PVC vinyl 

 

Handles

 

 

One on each side, one top, one bottom 

 

Grille

   

 

Perforated metal with weather- 

 

 

 

 

resistant coating 

Physical Properties

 

Height

 

   

4.9 in/111.6 cm 

 

Front Width

   

19.1 in/48.5 cm 

 

Rear Width

   

1.9 in/5. cm

 

 

Depth

     

 

18.1 in/46.0 cm 

 

Weight 

 

111 lb/50 kg 

 

Mounting Methods

 

Floor mount only.

 

 

 

 

The SR150z should never be pole-mounted.  

 

 

 

The cabinet has no rigging points and is not  

 

 

 

suitable for flying. 

Never attempt to suspend the  

 

 

 

cabinet by its handles.

Disclaimer

 

Since we are always striving to make our products better by in-

corporating new and improved materials, components, and manufac-
turing methods, we reserve the right to change these specifications 
at any time without notice.
“Mackie” and the “Running Man” figure are registered trademarks 
of LOUD Technologies Inc.
All other brand names mentioned are trademarks or registered 
trademarks of their respective holders, and are hereby acknowledged.

©004-008 LOUD Technologies Inc. 
All Rights Reserved.

R

Summary of Contents for SR1530Z













Reviews: