background image

2

These instructions are intended to help restore any ailing SA1521z Active 

Loudspeaker back to factory working conditions. They show how to remove and 

replace the drivers and the amplifi er assembly.

Please contact Mackie Tech Support (1-800-898-3211) to receive a Service 

Request Number and Order Number for parts needed for this restoration. They will 

also help you determine the nature of the problem and what parts will repair the unit. 

Tools needed:

***NOTE: not all tools listed below will be needed for your repair***
•  Phillips head screwdriver.
•  3mm and 4mm allen wrench.
•  10mm open end wrench OR 13/32 inch socket.
• Solid 

workbench.

•  Non-carpeted work area due to static electricity. If available, an ESD mat 

(Electro-static discharge) is optimal. 

Parts needed: 

 

***NOTE: not all parts listed below will be needed for your repair***
• 

Led 

PCB 

Assembly 

  Part 

#0007334 

  pages 

3-4

• 

15” 

Woofer 

   Part 

#0013918 

  pages 

5-6

•  High Frequency Driver   

Part #0013925 

 

 

pages 7-9

• 

Diaphragm 

   Part 

#coming 

soon  page 

 

10

• Amplifi er Assembly  

 

Part #0013838-00   

 

pages 11-13

Safety Warnings:

•  Make sure that you turn off the unit and disconnect the power cord (and all 

other cords) before you begin these procedures.

•  Always use safety glasses!
•  Please try NOT to touch any of the pcb circuitry, capacitors, resistors, etc.
•  Take care to read and follow these instructions. It may help to read the 

 instructions prior to the repair to get an idea of what it entails. 

•  Before beginning the repair, touch metal to discharge any lingering internal 

static electricity. 

Summary of Contents for SA1521Z














Reviews: