background image

6

  33

 

Carefully begin to remove the woofer.

   

Caution:

 The woofer is approximately 

8 pounds with the weight unevenly 

distributed.

Top right woofer replacement continued:

  44

 

The positive (blue and black) and 

negative (solid black) cables are still 

attached to the woofer terminals. 

Remove the cables from their terminals 

simply by pushing down on the terminal 

and pulling out the cable.

  55

 

The picture above shows what the S408 

looks like with the grill and top right 

woofer removed. Place the new woofer 

(part #0011806) where the old one was. 

Follow the same steps as above, but 

backwards 4 to 1. Power up the S408 

and the new woofer should now be 

pumping out glorious lows. Awesome, 

you just replaced an 8” woofer!

++

--

push down

push down

 

**

 

If you fi nd it too diffi cult to connect the 

cables to the woofer terminals due to 

the short length of the cables, there 

is an easier (albeit lengthier) way to 

connect them. Instead of reconnecting 

the cables to their terminals, just attach 

the woofer to the cabinet as normal. 

Follow steps 1-5 on how to remove the 

horn assembly (pages 11-12) as this is 

an easier way to access the woofer 

terminals without having to work under 

such tight circumstances! 

Summary of Contents for S408




















Reviews: