background image

High-Current Power Amplifier

M•2600

AMPLIFIER

M•2600

oF 6 PAGES

2

O F   6   P A G E S

High-Current Power Amplifier

M•2600

oF 6 PAGES

3

O F   6   P A G E S

High-Current Power Amplifier

M•2600

oF 6 PAGES

4

O F   6   P A G E S

M•2600 Specifications

Maximum Power mid-band at 1% THD:

500 watts per channel into 8 ohms
850 watts per channel into 4 ohms
1300 watts per channel into 2 ohms
1700 watts into 8 ohms bridged mono
2600 watts into 4 ohms bridged mono

Continuous Sine Wave Average Output Power, both 
channels driven (20Hz - 20kHz):

425 watts per channel into 8 ohms  <0.025% THD
700 watts per channel into 4 ohms  <0.050% THD
1000 watts per channel into 2 ohms  <0.1% THD

Bridged mono operation (20Hz - 20kHz):

1400 watts per channel into 8 ohms:                   <0.05% THD
2000 watts per channel into 4 ohms                      <0.1% THD

Power Bandwidth:

20Hz to 70kHz (+0,  –3dB) @ 700 Watts into 4 ohms

Frequency Response:

20Hz to 40kHz (+0,  –1dB)
10Hz to 70kHz (+0,  –3dB)

Distortion:

THD, SMPTE IMD, TIM
  <0.025%@8

Ω

  <0.050%@4

Ω

  <0.150%@2

Ω

Signal to Noise Ratio

>107dB relative to rated power into 4 ohms

Channel Separation:

>80dB@1kHz

Damping Factor:

>350 from 0 to 400Hz

Input Impedance:

24k

Ω

 balanced bridging

Input Sensitivity:

1.23 volts (+4 dBu) for rated power into 4 ohms

Gain:

32.7 dB (voltage gain of 43)

Maximum Input Level:

9.75 volts (+22 dBu)

Rise Time:

<5

 µs

Slew Rate:

Voltage Slew Rate 

>60V/µs

Current Slew Rate 

>30A/µs at 2

Ω

CMRR:

>40 dB, 20Hz to 20kHz

Transient Recovery:

<1µs for 20dB overdrive at 1kHz

High-Frequency Overload and Latching:

No latch up to any frequency or level

Variable Low-Cut Filter:

10Hz (Off) to 170Hz, 2nd Order Bessel

Internal Crossover:

Switched 60Hz/90Hz/120Hz, 4th Order Linkwitz-Riley
Amplifier input is low-pass filtered when switched to sub-

woofer mode
Low-pass and high-pass outputs switchable to thru output 

jacks

Limiter Section:

Complementary Positive and Negative Peak Detecting

Indicators:

6 meter LEDs per channel

SIG (Signal Present), –20, –9, –6, –3, OL (Overload)

CH1 & 2

PROTECT LEDs

SHORT LEDs

TEMP STATUS

COLD/HOT LEDs

Power Consumption:

1650 watts (18.2A)   with musical program fully loaded

 

(2

Ω

 per side, or 4

Ω

 bridged)

AC Line Power:

US  

120 VAC, 60Hz

Europe 

240 VAC, 50/60Hz

Japan 

100 VAC, 50/60Hz

Korea 

220 VAC, 60Hz

AC Drop-out Voltage:

At approximately 63% of rated line voltage

Physical:

Height: 

  5.20" (132mm)

Width: 

19.00" (483 mm)

Depth: 

15.65" (398 mm)

Overall Depth: 

16.67" (423 mm)

Weight: 

55 lbs (25 kg)

T

R

I

M

 

 

3

/

4

 

 

O

F

F

 

 

T

H

I

S

 

 

E

D

G

E

Summary of Contents for FR Series M.2600







Reviews: