Macherey-Nagel 162735 Instructions For Installation Manual Download | Manualshive

Page: 3 / 21

background image

3/21

3. Installation of the Network Adapter

NOTICE

Use only the approved power supply.

NOTICE

If you are not going to use the device for a longer period, take it out of operation and disconnect it from
the power supply.

Connect the Network Adapter to the power supply via the connector as indicated in pic. 1. The device will start
up and can now be configured as described in chapter 4. Please note that a WiFi antenna can be mounted on
the blue marked connector (pic. 1).

Pic. 1: Power supply connection

«
1
2
3
4
5
...
»

Summary of Contents for 162735






















Reviews:

No comments

Related manuals for 162735

Brand: D-Link Pages: 43

Brand: Zonet Pages: 63

miniSD SCHF Series

Brand: Alps Electric Pages: 2

Brand: Tekram Technology Pages: 4

Brand: ConvaTec Pages: 4

Brand: Hamlet Pages: 2

Brand: NEC Pages: 7

Brand: Z-Com Pages: 46

Brand: Hama Pages: 22

Brand: Hama Pages: 53

Brand: Inteltronic Pages: 1

Brand: NCR Pages: 16

Brand: NCR Pages: 38

Brand: insys icom Pages: 100

Brand: Lenze Pages: 6

Brand: Arion Pages: 18

LINKSYS WMP300N

Brand: Linksys Pages: 71

Brand: Lanpro Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands