CDM Programming Mode: Windrower Setup
SET KNIFE SPEED
SPM
Adjusts knife speed on draper and auger headers.
Every header size and type of knife drive will have a different knife speed range.
Refer to your header quick card for optimal settings.
KNIFE
/
DISC OVERLOAD
SPD
SPM/RPM
KNIFE OVERLOAD SPEED (Auger/Draper) and DISC OVERLOAD SPEED (rotary)
Recommended setting is 75% of knife/disc speed.
Range is
−
100 to
−
500 SPM/RPM. Default setting is
−
300 SPM/RPM.
OVERLOAD PRESSURE
PSI/BAR
Calibration of overload sensor (reel/draper/knife/disc system).
Refer to the Suggested Overload Warning Setting column in chart below.
HEADER INDEX MODE
Reel + Drapers
OR
Reel only
Applies to auger and draper headers only.
References and operates reel only or reel and drapers in relation to ground speed.
RETURN TO CUT MODE
Tilt or Height only
Controls functions to be controlled by RETURN TO CUT mode.
Provides preset cutting height and tilt angle settings for headers.
Refer to operator’s manual for set-up procedure.
AUTO RAISE
←
10.0
→
Sets the header up height in RETURN TO CUT mode.
DWA INSTALLED
YES/NO?
Activates electrical controls for double windrow attachment (DWA) when installed.
SWAP DWA CONTROLS
NO/YES?
If YES is selected, swaps functions between the REEL FORE-AFT buttons on the GSL and
the DWA RAISE/LOWER switches on the console.
HEADER CUT WIDTH
##.# FT/M
Sets cut width according to operating width and affects the calibration of acre counter.
Header ID displayed on CDM at top right.
HDR REEL SPD
RPM or MPH/KMH
Allows REEL SPEED to display in rpm, mph, or km/h.
SET TIRE SIZE
Selects the installed tire size for ground speed and acre counter calibration.
SET ENGINE ISC RPM
NO/YES?
ENGINE INTERMEDIATE SPEED CONTROL. Engine rpm can be limited to a specified value
while header is engaged. Scroll to the desired rpm value and use the HAZARD key to set.
SET CONTROL LOCKS
NO/YES?
Allows header functions to be locked from Operator control
(for example, locking reel speed and/or reel fore-aft controls from Operator).
VIEW CONTROL LOCKS
NO/YES?
Allows Operator to view control lock status and engine hours when status was established
(for example, REEL FORE-AFT - 224.5 HRS LOCKED).
Tips and Shortcuts
Enter
Programming
Mode
Ignition ON.
Press and hold
PROGRAM
and
SELECT
at
the same time until the CDM display enters
programming mode.
Exit
Programming
Mode
Press
PROGRAM.
Change
Language to
English
Ignition OFF.
Press and hold
HEADER INDEX
and
PROGRAM
and
SELECT.
Clear
Sub-Acres
Cab-forward position.
Ignition ON.
Press
SELECT
until SUB-ACRES is viewed
on the bottom line of the display.
Press and hold
PROGRAM
until SUB-ACRES
changes to 0.0.
Header Model
Application System
Suggested Overload
Warning Setting kPa (psi)
Windrower Differential
Relief Setting kPa (psi)
R-Series
Disc pressure
37,232 (5400)
37,900 (5500)
Reel/draper pressure
19,995 (2900)
20,000 (2900)
Knife/conditioner pressure
27,579 (4000)
27,500 (4000)
D- and A-
Series
Enhanced reel/conveyor speed controls may be
desirable in variable crop and terrain conditions.
Header index mode allows the reel and conveyor to
be driven by reference to ground speed, so that
header systems will speed up and slow down as
ground speed changes.
Operation of Header Index for REEL SPEED:
(A- and D-Series)
1. With all bystanders clear, start windrower and
engage the header.
2. While stationary and with the GSL in PARK, use
the REEL SPEED control switch to set a
minimum reel speed.
When operating at ground speeds faster than the
minimum reel speed + header index value,
REEL SPEED display will change to
REEL INDEX. Using the REEL SPEED switch on
the GSL, header index can be adjusted.
Reel speed will be equal to the greater of:
Ground Speed + Index Value
or
Minimum Reel Speed
.
Operation of Header Index for DRAPER SPEED:
(D-Series only)
Follow instructions above using the CDM AUGER/
DRAPER speed control rather than the GSL REEL
SPEED switch.
Header Index Mode
M205 Windrower Quick Card - Form 147957 Rev. A
Supplement to M205 Windrower Operator’s Manual
M205 Windrower Quick Card - Form 147957 Rev. A
Supplement to M205 Windrower Operator’s Manual
