![background image](http://html1.mh-extra.com/html/macdon/hc10/hc10_setup-operation-and-parts-manual_3195042060.webp)
215593
50
Revision A
4.
Press SELECT (C) until HAY CONDITIONER? is displayed on
the upper line.
•
NO/YES is displayed on the lower line.
5.
Press right arrow (B) to select YES. Press SELECT (C).
6.
Press PROGRAM (A) to exit programming mode or press
SELECT (C) to proceed to next WINDROWER SETUP action.
3.11.5
Running up the Conditioner
Running up the conditioner ensures the machine is assembled, connected, and functioning properly.
CAUTION
Never start or move the machine until you are sure all bystanders have cleared the area.
DANGER
To avoid injury or death from unexpected start-up of the machine, always stop the engine and remove the key from
the ignition before leaving the operator
’
s seat for any reason.
1.
Clear all bystanders from the area.
2.
Start the windrower and engage the header. Refer to the windrower unloading and assembly instructions or operator
’
s
manual for windrower operating instructions.
3.
Operate the conditioner slowly for 5 minutes, watching and listening
FROM THE OPERATOR'S SEAT
for binding or
interfering parts.
4.
Run the header for 15 minutes.
5.
Perform the header run-up check to ensure the machine is field-ready. Refer to the header unloading and assembly
instructions.
6.
Perform the run-up check as listed on the Predelivery Checklist (yellow sheet attached to this instruction
—
refer to
Predelivery Checklist, page 173
).
7.
Shut down the engine, and remove the key from the ignition.
3.11.6
Storing Manuals
Manual should be placed in the manual storage case when not in use.
$
Figure 3.73: Manual Storage Case
Place this manual in storage case (A) in the windrower. The
Predelivery Checklist (yellow sheet attached to this instruction
—
refer to
Predelivery Checklist, page 173
) should be retained by
either the Dealer or the Operator.
Summary of Contents for HC10
