background image

18

 

 

ATTACHING & DETACHING

 

 
 

ATTACHING ADAPTER TO TRACTOR (continued)

 

 

7. 

For 9030 Tractor & TV140 Tractor with MacDon 
Header Drive Pump:

 Lock pump torque arm to 

channel with clevis pin and lynch pin at (F). 

NOTE:

 For 9030 Tractor, turn pump torque arm 

180

°

 to reverse offset as shown at right. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
If adjustment of locking channel is required: 

 

Loosen bolts that secure channel (F) to frame. 

 

Slide pump onto PTO shaft until torque arm is 
against shield. 

 

Slide channel (F) back to contact torque arm 
and tighten bolts. 

 
 
8. 

For TV140 Tractor with NH Auxiliary Pump:

 

Connect ¾” male couplers (G) on hoses coming 
from relief valve in sickle drive circuit to auxiliary 
pump couplers on tractor.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
9. a) 

For all Headers except Model 910 Series:

 

Connect conveyor and reel drive ¾” male couplers (H) 
to tractor, ensuring RETURN coupler (with black cable 
tie) goes to the RETURN coupler on the tractor.  
To identify 3/4 inch PRESSURE and RETURN couplers 
on tractor: Return coupler is connected to a single larger 
hose. For 9030 Tractor, pressure coupler is attached to 
two smaller hoses, one of which is routed to BLUE-
EXTEND coupler. For TV140 Tractor, pressure coupler 
is attached to a steel line that is routed to BLUE-
RETRACT coupler. 
Place the extra black cable tie (provided with adapter) 
on the tractor RETURN port for ease of identification. 
 b) 

For Model 910 Series Header & Adapter with 

MacDon Pump Only:

 Attach reel drive hose (yellow 

cable tie) to tractor blue circuit coupler (X). Reduce flow 
to 8 gpm. Attach conveyor return hose (blue cable tie) to 
tractor blue circuit coupler (Z). 

NOTE:

 To connect 

conveyor hose, order 21855 male coupler (2) and 34420 
hose. 
 c) 

For Model 910 Series Header & Adapter with 

NH Auxiliary Pump

: No conveyor or reel circuit hose 

connections are required. 
 
10.  Connect ½” female case drain coupler (J) to tractor 

coupler. 

 
11.  Attach 7 terminal plug from adapter wiring harness 

into tractor at (K). Attach 12-pin connector (L) to 
header control panel plug coming from tractor. 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

LOCK PUMP TORQUE ARM – TV140

LOCK PUMP TORQUE ARM - 9030

CONNECT SICKLE DRIVE HOSES

TV140 with AUXILIARY PUMP 

HYDRAULIC & ELECTRICAL CONNECTIONS 

(TV140 without AUX. PUMP SHOWN) 

Summary of Contents for 802














































Reviews: