manualshive.com logo in svg

M2 Antenna Systems SYSTEM SAMPLE 3, Assembly Manual

Share
Download
M2 Antenna Systems SYSTEM SAMPLE 3 Assembly Manual Download Page 11

 
BAG #5 (STEP 5) 

Bolt, 1/4-20 x 3/4” Hex Head S.S................................................................. 6 
Lock Washer, 1/4” S.S. ................................................................................ 6 
 

BAG #6 (STEP 6) 

Screw, 6-32 x 1/2”, Pan Head Phil S.S. ....................................................... 18 
Lock Washer, 6-32 S.S. ............................................................................... 18 

 
BAG #7 (STEP 7) 

Bolt, 1/4-20 x 1-1/4” Hex Head S.S.............................................................. 3 
Lock Nut, 1/4-20 S.S.................................................................................... 3 

 
BAG #8 (STEP 8) 

Bolt, 3/8-16 x 1” Hex Head S.S.................................................................... 4 
Lock Washer, 3/8” S.S. ................................................................................ 4 
Flat Washer, 3/8” S.S................................................................................... 8 

 
BAG #9 (STEP 9) 

Bolt, 1/4-20 x 2” Hex Head S.S.................................................................... 3 
Bolt, 1/4-20 x 1-3/4” Hex Head S.S.............................................................. 6 
Flat Washer, 1/4” S.S................................................................................... 6 
Lock Nut, 1/4-20 S.S.................................................................................... 9 

 
BAG #10 (STEP 10) 

Bolt, 3/8-24 x 2” Hex Head S.S.................................................................... 2 

 
BAG #11 (STEP 11) 

Bolt, 3/8-16 x 3/4” Square Head S.S............................................................ 2 

 
BAG #12 (Miscellaneous Hardware) 

Screw, 8-32 x 1/2” Set S.S........................................................................... 4 
Screw, 6-32 x 1/2” Pan Head Phil S.S. ........................................................ 12 
Lock Nut, 6-32 S.S....................................................................................... 12 
Allen Key, 5/64”. .......................................................................................... 1 
 
 

 
 
 

 PARTS & HARDWARE 

 

Carefully manufactured by:  

 

M2 Antenna Systems, Inc. 

4402 N. Selland Ave. Fresno, CA 93722 

(559) 432-8873 Fax (559) 432-3059 

Web: www.m2inc.com 

Summary of Contents for SYSTEM SAMPLE 3

















Reviews:

No comments

Brands by name

Popular brands

Load more brands