background image

M.T.H. HO SD70ACe & SD70M-2 Diesel Engine

24

Lights 

Solution 

One of my lights is out 

Most likely you had been r unning the 
engine in DCC or DCS mode and 
toggled that light of f. Put it back into 
one of those modes and tur n that light 
back on. The engine will r emember 
that when you run it again  in 
Conventional DC. 

None of my lights are on 

Could be the same reason as “One of 
my lights is out” 

 

Is the engine getting po wer? Check to 
see if there is voltag e on the track or 
move the engine a few feet  in either 
direction. 

Motion 

Solution 

When I apply power to the 
track my engine starts up 
(lights and sound) but it won’t 
move 

Lower the track voltage then raise it 
again. The engine should s tart 
moving. If you apply greater than 
9VDC quickly the engine will just set 
there. Lowering it below 9VDC then 
raising it will get the engine moving 

My engine hesitates at sl ow 
speeds 

An engine may do this right out of the 
box if it has not been lubricated. 
Follow the lubrication instructions. 
Now go ahead and run it. 

 

New engines even after th ey are 
lubricated may take a little bit to get 
everything run in. Be a little patient 
and let it run for a bit. It should clear 
up shortly after lubr icating and 
running 

Analog DC

Summary of Contents for RailKing RKS SD70ACE

































Reviews: