background image

  Premier SD60 MAC Diesel Engine

15  

The locomotive’s headlight is controlled by a constant voltage circuit in the engine.  The
headlight is easy to remove and replace when it burns out.  The bulb has a quick
disconnect plug that attaches the bulb harness to a connector terminal inside the body
shell.  Replacement bulbs are available directly from the M.T.H. Parts Department. 

Follow the body removal instructions found in the Lubrication and Greasing Instructions.

Gently disconnect the bulb harness from the socket on the constant voltage circuit or
connector terminal and replace the bulb.

The special NiCad 7-cell 8.4v self-charging battery recharges continuously during train
operation and  should last for up to five years.  The battery is a dry battery that should not 
leak or cause any damage to your engine.  Depending upon when your engine was built,
it may need to be charged right out of the box.  If engine sounds seem distorted or
garbled at low voltages or become silent when power from the transformer is turned off,
test the battery to determine whether it should be recharged or replaced.

Test:

  Put the engine in neutral and leave the track voltage at 10-12 volts (high enough

for the lights to shine brightly and the engine to move steadily) for 15 minutes.

Replaceable Lights

Replaceable Lights

Figure 7:  Removing The Replaceable Lights

Headlight Replacement Instructions

Self Charging Battery Back-Up

Summary of Contents for Premier SD60 MAC Diesel Engine




























Reviews: