background image

Premier Dreyfuss Hudson Steam Locomotive

M.T.H. engines equipped with Proto-Sound 2.0 have speed control capabilities that 
allow the engine to maintain a constant speed up and down grades and around curves, 
much like an automobile cruise control.  You can add or drop cars on the run, and the 
engine will maintain the speed you set. 

While the engine is programmed to start with the speed control feature activated, you 
can opt to turn it off.  This means the engine's speed will fall as it labors up a hill and 
increase as it travels downward.  It is also affected by the addition or releasing of cars 
while on the run. Because the engine will run more slowly at a given throttle voltage 
when speed control is on than when it is off, you should adjust the throttle to a lower 
power level for operation with speed control off to avoid high-speed derailments.  
When speed control is off, the volume will drop to allow for better low voltage 
operation.

To turn speed control on and off

, put the engine in neutral, then quickly tap the 

tranJ1eormer's Horn button one time then quickly tap the Bell button two times, 
allowing approximately ½ second to lapse between each quick button press.  Two horn 
blasts will indicate that the engine has made the change.  Repeat the 1 horn, 2 bells 
code to return it to the other condition.  You will want to do this during the initial 
neutral upon start-up if you ever couple this engine to another engine that is not 
equipped with speed control to avoid damaging the motors in either engine.  Each time 

Speed Control

Horn

Place 

Engine into 

Neutral

Bell

Bell

=

Speed Control

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

Locking Locomotive Into A Direction

You can lock your engine into a direction (forward, neutral, or reverse) so that it will not change 
directions.  To do this, put the engine into the direction you want (or into neutral to lock it into 
neutral), run it at a very slow crawl (as slowly as it will move without halting), and quickly but 
firmly tap the Horn button once followed by three quick taps of the Bell button, allowing 
approximately ½ second to lapse between each quick button press. Two horn blasts will indicate 
that the engine has made the change.  The engine will not change direction (including going into 
neutral) until you repeat the 1 horn, 3 bells code to return the engine to its normal condition, even 
if the engine is kept without power for extended periods of time.

Horn

Place 

Engine into 

Desired 

Direction

Horn

Bell

Bell

Bell

=

Direction Lock

Two Horn Blasts

(indicates change is made)

Repeat to Return

to Normal Condition

13

Summary of Contents for Premier Dreyfuss HudsonSteam Locomotive




























Reviews: