M.T.H. HO 2-8-8-4 Yellowstone Engineer'S Manual Download

Page: 4 / 47

UNPACKING YOUR ENGINE

Removing and Unwrapping Your Engine

Carefully remove and unwrap the model on a soft surface. By nature, models with
high levels of detail have some small fragile parts.

Carefully remove any foam packing pieces that may be surrounding the model.

What Else is in the Box?

The following items are packed with your engine.

Quick Start Guide (1)

For those who can’t wait to get started! This will give you the basic information to
get your engine up and running!

Smoke Fluid Pipette (1)

Enough fluid to get you started, and then some.

Rear Drive Wheel Set without Traction Tires (1)

For Those who prefer not to use traction tires.

Nut Driver (1)

In case you want to install the drivers with traction tires or replace the standard
drive wheels.

M.T.H. HO 2-8-8-4 Yellowstone Steam Engine

Summary of Contents for HO 2-8-8-4 Yellowstone
















































Search results

Summary of Contents for HO 2-8-8-4 Yellowstone

Reviews:

Related manuals for HO 2-8-8-4 Yellowstone

Brands by name

Popular brands

M.T.H. HO 2-8-8-4 Yellowstone, Engineer'S Manual

Search results

Summary of Contents for HO 2-8-8-4 Yellowstone

Reviews:

Related manuals for HO 2-8-8-4 Yellowstone

Brands by name

Popular brands