background image

R7L-RR8

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-7804-T  Rev.6  P. 2 / 14

COMPONENT IDENTIFICATION

ERR

SVCE

ONLINE

TX/RX

PWR

0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7

4

5

6

7

1

2

3

10 11 12 13

2

3

4

1

15 16 17 18

7

8

9

6

14

5

Reset SW

Factory Configuration Port

Service SW

Status Indicator LED

I/O Status Indicator LED

L

ON

W

ORKS

, Power Supply

Terminals

Output Terminals

 

STATUS INDICATOR LED

ID

COLOR

STATE

MEANING

PWR

Green

ON

Internal 5V is normal

OFF

Internal 5V is abnormal.

ONLINE Green

ON

Online

Blink

approx.

0.5 Hz

Offline
Sending/receiving of Net-
work
Variables has stopped.

Blink

approx.

2 Hz

Receiving Wink Message

OFF

Abnormal state

ERR

Red

ON

Writing in the non-volatile 
memory

Blink

Abnormal state

OFF

Normal state

TX/RX

Green

ON

Sending/receiving Network 
Variables

OFF

Communication is lost.

SVCE

Green

ON

No network information

Blink

approx.

0.5 Hz

Offline
Sending/receiving of Net-
work
Variables has stopped.

OFF

Normal state

 

I/O STATUS INDICATOR LED

Output and feedback input status are indicated with LED.
     

ON  

: LED ON

     

OFF  : LED OFF

 

SERVICE SWITCH

Used to identify the node in L

ON

W

ORKS

 network configura-

tion.

 

RESET SWITCH

Used to reset the Neuron Chip.  Press the switch behind the 
front cover to reset.
Control functions are halted while completing resetting and 
restarting.  Confirm no danger before conducting resetting.

 

POWER SUPPLY, L

ON

W

ORKS

 TERMINAL ASSIGNMENT

4

NET1

5

NET2

6

U (+)

1

NET1

2

NET2

3

FG

7

V (–)

NO.

ID

FUNCTION, NOTES

1

NET1

L

ON

W

ORKS

 communication 1

2

NET2

L

ON

W

ORKS

 communication 2

3

FG

FG

4

NET1

L

ON

W

ORKS

 communication 1

5

NET2

L

ON

W

ORKS

 communication 2

6

U (+)

Power input

7

V (–)

Power input

Note:   L

ON

W

ORKS

 wiring must be paired between NET1 termi-

nals and/or NET2 terminals.

 

OUTPUT TERMINAL ASSIGNMENT

10

NC

11

Y0

12

Y1

1

NC

2

C0

3

C1

13

Y2

4

C2

14

Y3

5

C3

15

Y4

6

C4

16

Y5

7

C5

17

Y6

8

C6

9

C7

18

Y7

NO.

ID

FUNCTION

NO.

ID

FUNCTION

1

NC

No connection

10

NC

No connection

2

C0

Common 

11

Y0

Output 0

3

C1

Common 

12

Y1

Output 1

4

C2

Common 

13

Y2

Output 2

5

C3

Common

14

Y3

Output 3

6

C4

Common

15

Y4

Output 4

7

C5

Common 

16

Y5

Output 5

8

C6

Common 

17

Y6

Output 6

9

C7

Common 

18

Y7

Output 7

Summary of Contents for R7L-RR8















Reviews: