MS-210U4P USER GUIDE
03
02
[email protected] | www.m4sol.com
MS-210U4P USER GUIDE
[email protected] | www.m4sol.com
Introduction
03
Key Features
03
Connectivity Overview (TX and RX)
04
Understanding the LED’s
05
Cabling for HDBaseT
05
Audio
05
USB
06
IR Control & RS-232 Control
06
Specifications & Package Contents
07
Schematic
08
Contents
Notices
• This MSolutions product contains electrical components that may be damaged by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of surge protection is highly recommended in order to protect and extend the life
of your equipment.
• The transmission distances of HDMI over Cat cables are measured using TE CONNECTIVITY 1427071-6 EIA/
TIA-568-B termination (T568B) of cables is recommended for optimal performance. To minimise interference of
unshielded twisted pairs in the CAT5e/6 cable, do not run the HDBaseT / Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables.
• Do not substitute or use any other power supply other than the enclosed unit, or an MSolutions approved
replacement. Do not disassemble either the Transmitter or Receiver units for any reason. Doing so will void the
manufacturer’s warranty.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
• Dolby is a trademark of Dolby Laboratories.
• MSolutions reserves the right to change the specifications of this unit without prior notice. As a result of this,
physical representations or graphical elements contained within this user guide may not be accurate.
Introduction
The MSolutions MS-210U4P is a 4K HDMI / KVM HDBaseT extender set allowing for uncompressed
video and audio to be extended up to 40m at 4K UHD (10.2Gbps), and 70m at 1080p or lower
resolutions.
4 x independent USB2.0 channels allow for bi-directional USB client to host connectivity for
connectivity of various peripherals in a variety of commercial applications.
The extender provides bi-directional RS-232 and a single channel IR link between TX to RX, or RX
to TX. Bi-directional PoC (Power over Cable) allows for either the TX or RX to be powered.
Key Features
• Uncompressed extension of HDMI at resolutions up to 4K 60Hz 4:2:0 / 4K 30Hz 4:4:4 using
HDBaseT technology
• 4K signal extension to 40m over single CAT including HDR formats suppported under 10.2Gbps
• 1080p or lower video resolutions up to 70m over single CAT
• Supports HDMI pass-through all known HDMI audio formats including Dolby Atmos / DTS:X
• Bi-directional 12V PoC (Power over Cable)
• 4 x USB2.0 channels for KVM connectivity of multiple USB devices across the link - max
200Mbps data rate pass-through (combined)
• Flexible USB extension for: USB2.0 cameras, touch screens, smart boards, hard drives, games
controllers, USB audio devices, printers, scanners, and HID’s (mouse or keyboard)
• Independent 1-way analogue audio pass-through (RX to TX)
• Bi-directional RS-232 serial pass through
• Single channel 5V IR pass-through (TX to RX, or, RX to TX)
• CEC (Consumer Electronics Control) pass through
• HDCP2.2 compliant
Video resolution capabilities - 10.2Gbps HDMI 1.4 specification max:
Resolution
Refresh
Chroma
Depth
4096x2160 (DCI)
3840x2160
50Hz / 60Hz
30Hz
24Hz
4:2:0
4:2:0 / 4:2:2 / 4:4:4 / RGB
4:2:0 / 4:2:2 / 4:4:4 / RGB
8-bit
8 / 10 / 12-bit
8 / 10 / 12-bit
1920x1080
up to 60Hz
4:4:4 / RGB
up to 16-bit
1280x720
1024x768
up to 60Hz
4:4:4 / RGB
up to 16-bit
VGA to WUXGA
up to 60Hz
