ENGLISH | ADV-300
7
ADV-300 OUTDOOR UNIT FOR THE
VISTADOOR INTERCOM SYSTEM
INTRODUCTION
Thank you for choosing the VISTADOOR intercom system. You have
purchased a high quality system with a stainless steel cover. The elabo-
rate stainless steel covers are made by hand and thus have individual
characteristics that should be considered a sign of quality.
NOTES ON CARING FOR STAINLESS STEEL
Please never clean the stainless steel surfaces with standard cleaning
materials, as these are too harsh. Please simply clean using spray desi-
gned for the cleaning and care of stainless steel. If this is not available
please use only clear water.
Brushed surfaces should always be cleaned with the grain and never in
a circular motion. This will avoid the creation of scratches.
Failure to observe these notes may lead to discolouration or even to
corrosion damage in extreme cases.
The system should be assembled by a specialist.
KEY
1 Outdoor unit
1.1 Wall box
1.2 Stainless steel front plate
2 Indicator field
4 Loudspeaker perforations
5 Bell button
6 Microphone
7 Casing screws
8 Lightness sensor
9 Volume potentiometer
10 Dip switch for the opening time of the door opener
11 Dip switch for the ID code
12 Connection terminal door opener
13 Connection terminal power supply
14 Connection terminal signal line
16 Installation aid
SCOPE OF DELIVERY
1x Outdoor unit
1x Wall box
1x Plaster aid
7x Torx screw for front plate (1pc. spare)
3x Installation aid incl. screw
8x Dowel and screw
PREPARATION FOR INSTALLATION
The following lines are required:
Single-family house: 3 lines from the outdoor unit to the indoor unit
and 2 lines from the outdoor unit to the door opener.
Multi-family house (from ADV-320): In this case 3 lines are required per
bell button from the outdoor unit into each residential unit.
Example ADV-340: 12 lines are required at the outdoor unit for the
residential units (3 lines each x 4 bell buttons) and 2 lines to
the door opener.
Up to four indoor units can be connected in parallel per residential unit.
The connection can either be laid from the indoor station or in a star
formation from a central point (distribution box).
The lines should be laid in such a way that they are fed out of the wall
directly behind the relevant outdoor/indoor unit.
Note: It is also possible to combine video and audio
components with the VISTADOOR system.
INSTALLATION OF THE OUTDOOR UNIT
The intercom system is designed to be flush-mounted.
Preparation
When removing the front cover, take care that the indicator field and
the nameplate do not fall out and get damaged.
The outdoor unit should be mounted at a height of approx. 1.5-1.6m
(middle of unit). If necessary, adjust the installation height and
location to suit the local conditions.
1. Remove the six screws from the stainless steel front plate using
a Torx screwdriver (T10) and then lift it upwards. Now you can
uncover the wall box by carefully removing the rubber seal and
taking out the actual outside station.
2. Hold the wall box straight on the wall and draw around it on the
wall with a suitable pencil. Take care that the necessary connecting
cables are in the middle part of the wall box. The cables should not
be measured too short.
3. The cable feedthrough can be detached with a sharp knife.
Note
:
The hole for the intercom system should be measured so that the wall
box fits precisely inside and is flush with the building wall.
4. In order to anchor the wall box to the wall, first use the holes in
the base of the wall box to mark the 8 fixing holes in the wall and
then drill corresponding holes (diameter approx. 6 mm).
5. Next place the supplied dowels in the holes. The wall box can now
be affixed with the 4 outer screws. Take care here to ensure that
the wall box is level; check this if necessary with a spirit level. The
wall box must also not be twisted.
NOTE
: If the wall box is affixed only insecurely by the screws, the
wooden frame can be filled along the sides with appropriate glue.
6. For plastering insert the supplied plaster aid into the wall box. This
prevents the wall box from being filled with mortar / plaster. When
plastering make sure that the threaded inserts will not be soiled
with mortar / plaster.
7. Insert the outer unit into the wall box. In order to prevent the outer
unit from falling out, use the supplied installation aid (16). It is
easily screwed to the wall box using one of the Torx screws and
holds the outer unit in position.
ADV-300_I-Manual_Fin1.indd 7
29.10.12 11:46
