LXNAV TrafficView Manual Download Page 8

Rev #5 

Version 1.01

 

July 

2020

 

 

 

Page 8 of 

34

 

of radio frequencies, aircraft installation, safety re

gulations, or regulations for sports 

competitions. 

 

3. 

Intellectual Property.

  No  part of the software, firmware, license keys, data 

(including  obstacle databases), the FLARM radio protocol and messages, and the FLARM 

hardware and design may be copied, altered, reverse engineered, decompiled or 

disassembled  without  an  explicit  and  writ

ten approval by FLARM Technology. Software, 

firmware, license keys, data (including obstacle databases), the FLARM radio protocol and 

messages, the FLARM hardware and design, and the FLARM logos and name are protected 

by copyright, trademark and patent laws. 

 

4. 

Manipulation.

 It is forbidden to intentionally feed artificially generated signals to the 

FLARM  device,  its  GPS  antenna  or  the  external/internal  GPS  antenna  connections,

  unless 

agreed with FLARM Technology in writing for limited R&D activities. 

 

5. 

FLARM Data and Privacy 

5.1.  FLARM devices receive, collect, store, use, send, and broadcast data to enable the 

system to work, improve the system, and to enable troubleshooting. This data may 

include, but is not limited to, configuration items, aircraft identification, own 

positions, and such data of other aircraft. FLARM Technology may receive, collect, 

store, and use this data for said or other purposes including Search and Rescue 

(SAR). 

5.2.

  FLARM Technology may share data with its partners for aforementioned or other 

purposes. FLARM Technology may in addition publicly make available data from a 

FLARM device (Flight Tracking). If a FLARM device has been configured to limit 

tracking, SAR and other services may not be available. 

5.3.  Data sent or broadcast by FLARM devices may only be used at own risk and under 

the same conditions as the FLARM device itself, and is encrypted partially to ensure 

message integrity, system safety and provide protection for the relevant content 

against eavesdropping, namely by article 3 of the Budapest Convention on 

Cybercrime as signed and ratified by most countries respectively its national 

implementations. FLARM Technology is not responsible for any third party device, 

software, or service receiving, collecting, storing, using, sending, broadcasting, or 

making publicly available data regardless of whether legally or illegally. 

 

6. 

Warranty, Limitation of Liability, and Indemnification 

6.1.  Warranty.

 FLARM devices, software, firmware, license keys, and data are provided 

on an "as is" basis without warranty of any kind — 

either  expressed  or

  implied  — 

including, without limitation, any implied warranties of merchantability or fitness for a 

particular purpose. FLARM Technology does not warrant the performance of the 

device, software, firmware, license key, or data or that the device, software, 

firmware, license key, or data will meet your requirements or operate error free.

 

6.2.  Limitation of Liability.

 In no event shall FLARM Technology be liable to you or any 

party related to you f

or any indirect, incidental, consequential, special, exemplary

, or 

punitive damages (including, without limitation, damages for loss of business profits, 

business interruption,  loss of business information, loss of data or other such 

pecuniary loss), whether under a theory of contract, warranty, tort (including 

negligence), products liability, or otherwise, even if FLARM Technology has been 

advised of the possibility of such damages. In no event will FLARM Technology’s total 

aggregate and cumulative liability to you for any and all claims of any kind arising 

hereunder 

exceed the amount of fees actually paid by you for the device, license keys 

or data giving rise to the claim in the twelve months  preceding the claim. The 

Summary of Contents for TrafficView



































Reviews: