background image

Introduction 

MX3 Multi-Charger Plus User’s Guide 

 

E-EQ-MX3MCPLUS-E  

 

Chapter 2 Installation and Operation 

Introduction 

The life and capacity of a Lithium Ion battery pack can vary significantly depending on the 
discharge current and the environment in which it is used. As with all batteries, expect to see a 
reduction in the total number of operations a fully charged battery pack can deliver as it ages. 
Charging times may increase but will not exceed four hours. Battery packs do not need to be fully 
discharged between charge cycles. 

The analyze feature allows you to determine the current condition of the battery pack. The 
capacity of the battery (in mAH) can be compared to the battery specification. Expect a battery 
pack with less than 80% of its rated capacity to provide noticeably shorter operating time for your 
mobile device. 

LXE Battery Pack Part Number 

156213-0001 
2381A376BATT1600 

158224-0001 
MX3A378BATT  

and 

159922-0001 
MX3A380RFIDBATT 

Construction 

Lithium Ion 

Lithium Ion 

Specified Capacity 

1400mAh 1800mAh 

80% of Specified Capacity 

1120mAh 1440mAh 

Normal Operations 

The optimal operating temperature range for the Multi-Charger Plus is between 50°F and 95°F 
(10°C and 35°C). While charging, the charger/analyzer and battery pack will generate enough 
heat to feel warm. This is normal and does not indicate a problem. Do not store the battery pack in 
direct sunlight or anywhere the battery pack cannot cool down. If the battery pack is hot after 
removal from the computer, allow it to cool at room temperature before placing it in the charger.  

Charge times may increase significantly if the battery is warm or hot, since it takes the battery 
pack longer to cool down while in the charger pocket. If the battery pack is hot from severe 
environmental use and immediate recharging is necessary, place the battery pack in a cool air 
stream or in a cool location until it is no longer warm to the touch before charging. 

Maintenance 

Use a clean soft cloth to wipe any dirt, moisture or grease from the battery pack, contacts or the 
charger. Do not use any liquid to clean the battery pack or charger contacts. 

Summary of Contents for 9000A3775

































































Reviews: