Luxul Xen XGS-1008 User Manual Download Page 10

User Guide

10

© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

5: REGULATORY COMPLIANCE

This device is approved under the Luxul brand and designed to comply for use spe-
cifi cally with other approved Luxul devices. This device is designed to be compliant 
with rules and regulations in locations where they are sold and will be labeled as 
required. Any changes or modifi cations to Luxul equipment, not expressly ap-
proved by Luxul, could void the user’s authority to operate the equipment. This 
Luxul device when used in conjunction with the approved Luxul Models should be 
professionally installed and the Radio Frequency Output Power will not exceed the 
maximum allowable limit for those countries that have regulatory approval.

5.1 Health and Safety Recommendations

Warnings for the use of Wireless Devices: Please observe all warning notices with 
regard to the usage of wireless devices

Potentially Hazardous Atmospheres: You are reminded of the need to observe 
restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas 
where the air contains chemicals or particles (such as grain, dust, or metal powders).

Safety in Hospitals: Wireless devices transmit radio frequency energy and may 
affect medical electrical equipment. When installed adjacent to other equipment, 
it is advised to verify that the adjacent equipment is not adversely affected.

Power Supply: Use only a Luxul approved power supply output rated at 9VDC and 
minimum 0.6A. The power supply shall be Listed to UL/CSA 60950-1; and certifi ed 
to IEC60950-1 and EN60950-1 with SELV outputs. The device can also be powered 
from a compliant POE source. Use of alternative power supply will invalidate any 
approval given to this device and may be dangerous.

5.2 FCC Statement:

This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment uses and can radiate radio frequency energy, and if not 
installed and used in accordance with the instructions may cause harmful interfer-
ence to radio communications. However; there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:

Summary of Contents for Xen XGS-1008













Reviews: