Luxul XAP-1510, Quick Install Manual

Page: 6 / 8

Fold Fold Fold
Next,„connect„an„Ethernet„cable„from„your„Router„or„Switch„to„the„ Data
IN
„port„on„the„PoE„Injector.„Finally,„connect„the„AC„cord„to„the„included„
PoE„Injector,„then„to„the„AC„outlet.
n
n
Note: nCategory-6nshieldedntwistednpairnisnrecommendednfornbestnn
resultsnandnstablendatantransmissionnatnthenhighestndatanrates.n
However,nCAT5/CAT5e/CAT6nUTPncablencannalsonbenused.
PoE Injector Setup
„ X
Data In:
„Connect„an„Ethernet„cable„from„your„router„or„switch„to„the„
Data In „port„of„the„included„PoE„Injector
„
X
Data & PWR Out: „Connect„an„Ethernet„cable„from„the„ Data & PWR Out „
port„of„the„included„PoE„Injector„to„the„PoE„Port„of„the„XAP-1510
„ X
AC Power:
„Connect„the„included„AC„Cord„to„the„Power„Input„of„the„
Included„Injector„first„and„then„to„the„AC„outlet.
Power
Source
From your
Router or Switch
Luxul AP
DATA IN
DATA &
PWR OUT
POE
Injector
PoEninjector
3
Preparing for Access
IP Addressing
If„the„XAP-1510„is„connected„to„a„network„with„a„192.168.0.X„address„
scheme,„and„your„computer„shares„a„similar„address„on„the„same„network,„
you„can„skip„to„the„next„step,„
Access and Setup
.
n
n
Note:
nnnIfnanotherndevicenonnyournnetworknsharesnthen192.168.0.10n
address,nyou’llnneedntontemporarilynreassignnornremoventhatn
devicenwhilenyounconfigurenthenXAP-1510.
If„your„network„uses„an„address„scheme„other„than„192.168.0.X,„you’ll„need„
to„set„a„temporary„static„IP„address„on„the„computer„you’re„using„for„config-
uration.„To„do„so,„set„the„IP„address„of„your„computer„to„an„address„in„the„
192.168.0.X„range,„then„set„the„Gateway/Router„address„to„192.168.0.10„(the„
default„IP„address„of„the„XAP-1510).
Once„you’re„finished„configuring„the„AP,„you„can„return„your„computer’s„IP„
configuration„to„normal,„typically„“Obtain„Automatically/DHCP.”
n
n
Note: nnnVisitn http://luxul.com/ip-addressing ntonlearnnmorenaboutn
changingnyourncomputer’snIPnaddressnandngettingnconnected.
4
Access and Setup
Getting Connected
„ X
Connecting Via an Ethernet Device:
„Use„Ethernet„cable„to„connect„
your„computer„to„the„PoE„switch„or„PoE„injector„to„which„the„XAP-1510„is„
connected.„Ethernet„is„the„preferred„method„of„connection.
„ X
Connecting Via a Wireless Device:
„Connect„your„client„device„to„the„
XAP-1510„default„wireless„network„named„Luxul1510.„The„wireless„network„
will„run„in„Open„Security„mode,„so„no„passphrase„is„required„until„Wireless„
Security„is„configured.„
Logging In
To„access„the„AP’s„web„configuration,„open„your„web„browser„and„enter„the„
AP’s„default„192.168.0.10„IP„address„in„the„address„field.„Log„in„to„the„AP„using„
the„default„user„name„and„password:
„
Default IP: 192.168.0.10
Username: admin
Password: admin
n
n
Note: nnnIfnanotherndevicenonnyournnetworknsharesnthen192.168.0.10naddress,n
you’llnneedntontemporarilynreassignnornremoventhatndevicenwhilen
younconfigurenthenXAP-1510.
n
n
Note: nnThenXAP-1510nisnnotnanrouternandnwillnneedntonbenconnectedntonan
networknwithnanrouterninnorderntondelivernInternetnaccess.
5
Hardware Operation
LED Indicators
Enclosure:
If„the„green„Power„LED„is„on,„the„XAP-1510„is„powered„and„working.„
If„the„Power„LED„is„OFF,„the„AP„is„not„receiving„power„or„the„LED„has„been„
turned„off„in„the„AP’s„web„interface.„If„the„green„Power„LED„is„blinking,„the„
XAP-1510„is„booting.„The„two„blue„LEDs„indicate„indicate„each„of„the„2.4GHz„
and„5GHz„networks„are„configured„and„broadcasting.
XAP-1510nLED’s
PoE Injector: If„the„PWR„LED„is„On,„Power„is„Connected„to„the„injector.„If„
the„PWR„LED„is„Off,„the„injector„is„not„receiving„power.„„
Reset Button
The„Reset„button„is„located„underneath„the„mount„and„
marked„RESET.„It„may„be„used„to„reboot„the„AP„or„to„restore„
factory„default„settings.
Reboot the AP: „With„the„XAP-1510„powered„on,„simply„
press„and„release„the„Reset„button.
Restore Factory Defaults:
„With„the„XAP-1510„powered„on,„
press„and„hold„the„Reset„button„for„10„seconds,„then„release„
the„button„and„the„XAP-1510„will„restore„factory„defaults„and„reboot.
n
c
CAUTION: nnHoldingnthenResetnbuttonnfornmorenthannanfewnsecondsn
willnrestorenthenAPntonfactoryndefaultnandnremovenanyn
customnconfiguration.
n
n
ERP Statement:
nnThenpurposenofnthisnproductnisntoncreatenanconstantn
networknconnectionnfornyourndevices.nItndoesnnotnhavenanstandbyn
modenornusenanpowernmanagementnmode.nIfnyounwishntonpowerndownn
thisnproduct,npleasenunplugnitnfromnthenpowernsocket.