background image

5

User Guide

© 2014  Luxul. All Rights Reserved.

Other trademarks and registered trademarks are the property of their respective owners

1.2 Site Preparation

 

„

Consult your site survey and network analysis reports to determine  
specific equipment placement, power drops, and so on.

 

„

Assign installation responsibility to the appropriate personnel.

 

„

Identify and document where all installed components are located.

 

„

Ensure adequate, dust-free ventilation to all installed equipment.

 

„

Identify and prepare Ethernet connection.

 

„

Verify that cable lengths are within the maximum allowable distances  
for optimal and certified signal transmission.

2 XAP-1500 SPECIFICATIONS

Standards Compliance

802.11n (900Mbps)

Interface

Two 10/100/1000M Ports

Antenna

Three Internal 5GHz and Three Internal 2.4GHz High 
Performance Antennas

Button

Reset button

Power

PoE (Injector Included)

Dimensions D x H in. (mm)

8”x1” (203.2x25.4)

LEDs

Power, 2.4GHz, 5GHz  
(Can be turned Off/On Via User Interface)

Wireless and Other Features

Frequency

Concurrent 2.4GHz and 5GHz

Wireless Speed

 

„

2.4GHz: 450Mbps; 

 

„

5GHz: 450Mbps.

Wireless Security

64/128bit WEP, WPA-PSK, WPA2-PSK, WPA/WPA2

Operating Modes

Wireless AP

Other Functions and Features

 

„

Remote Web Management

 

„

System Logging

 

„

Backup & Restore Configurations

 

„

VLAN/Guest Network Support

 

„

Support for Setup on iOS and  
Android Devices

 

„

QoS Support

 

„

Up to 12 SSIDs

 

„

Firmware Upgradeable via Browser

Certifications

CE, FCC, RoHS

Summary of Contents for XAP-1500





























Reviews: