background image

4 / 16

Adjusting Table Height:

1 .  Make sure no objects will obstruct 

the table when adjusting table 

height.

2 .  In order to run the table up/down, 

press the controller buttons with 

an arrows pointing up and down 

respectively.

3 .  Unplug the hand controller when 

not in use to prevent unauthorized 

use. 

Safety Regulations:

•  When the table is run up/down, 

keep a safe distance to avoid the 

risk of being squeezed between 

the moving table top and fixed 

objects in the surrounding area.

•  When the table is run up/down 

the user shall keep watch so that 

nobody is injured or no object is 

damaged. The table top must not 

bump into a fixed object so that 

the table is overturned. Always 

remove any office chair before the 

table is run up/down.

•  When the table is left unattended, 

the hand control plug must be 

unplugged and placed out of 

reach of children.

•  The table tripod must not be 

altered or reconstructed in any 

way. In service and repair work of 

the table, the electrical cable must 

always be disconnected from the 

wall socket.

•  Alterations to the control box are 

absolutely forbidden!

•  The table must not be used as a 

hoisting device for persons.

Maintenance and Repair:

•  After approximately one (1) week 

of use, check that the screws are 

properly tightened.

•  If the table cannot be lowered or 

raised, check the connections 

between the legs and the wall 

socket and be sure the plugs 

are inserted fully into the power 

supply.

•  If any part of the electrical system 

should need to be replaced, 

disconnect the electrical cable 

from the wall socket before 

replacing the electrical part to 

avoid risk of injury. After the 

electrical part has been replaced, 

connect the electrical cable back 

to the wall socket. The table is 

now ready for use.

•  If the table still does not work 

please contact your local dealer.

SAVE
 THESE INSTRUCTIONS

This device complies with part 15 of 

the FCC Rules. Operation is subject to 

the following two conditions:

1 .  This device may not cause harmful 

interference, and

2 .  This device must accept any 

interference received, including 

interference that may cause 

undesired operation.

WARNING

Changes or modifications not 

expressly approved by the party 

responsible for compliance could void 

the user’s authority to operate the 

equipment.

The crossed-out wheeled bin symbol 

indicates that the item should be disposed 

of separately from household waste. The 

item should be handed in for recycling 

in accordance with local environmental 

regulations for waste disposal. For more 

information please contact your dealer.

1 .

1 .

2 .

2 .

3 .

Summary of Contents for STANDE-48-AG/BO
















Reviews: