background image

 

 

 

Product Name: 

Cement Modern Rectangular Outdoor Fountain   

 

SKU #: 

WHF926 

 

Contact: [email protected] 

Instruction Manual 

Please save this manual for future reference. 

Pump Instructions:   

Special Warnings and Cautions:

 

 

 

CAUTION:

 

 

The pump has been evaluated for use with water only. 

 

Risk of electric shock. Do not remove cord and strain relief. Do not connect conduit to pump.   

 

Do not use the pump in water exceeding 30ºC / 86ºF. 

 

Do not use the pump in flammable liquids.   

 

Do not use the pump for industrial purposes.   

 

Do not use the pump in vehicles or on ships or aircraft or swimming pools.     

 

Do not use the pump in location where special conditions prevail, such as the presence of a corrosive or 
explosive atmosphere (dust, vapor or gas). 

 

Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling. 

 

Do not lift the pump by its power cord. 

 

Keep the plug dry. Do not expose the plug to water or steam. 

 

Before connecting to the power source, make sure that the pump is assembled and completely submerged 
in water. 

 

Always disconnect the pump from the power source before performing any maintenance on the pump, 
lights (if equipped), or fountain. 

 

Do not exceed the voltage shown on the pump. 

 

Check the water level regularly to ensure the pump is completely submerged during operation. The pump 
should be fully submerged during operation. Do not add water while operating the product. Always 
disconnect the pump from the power source before adding water. 
 

MAINTENANCE OF YOUR FOUNTAIN: 

 

Keep water clean 

using clean water will reduce mineral deposits and improve water clarity. 

 

Clean the fountain periodically to prevent mineral deposits and contamination. Use warm soapy water and a 
stiff brush for heavily stained surfaces. 

Do not use harsh chemicals as this will damage the finished surface 

and void the warranty.

 

 

Add clean water periodically to ensure that the pump is fully submersed in water. 

 

Disconnect the power and empty the basin if the fountain will not be used for an extended time. 

 

If installed outdoors and in a freeze-area of the country, ensure that all water is removed and the unit is 
completely dry. 

This product is NOT to be operated below 41

 (5

) freeze damage may occur. 

 

 

 

 

Summary of Contents for WHF926






Reviews: