background image

PowPak | Installation

Programming without a Vive Hub

Control Module with DALI

Part of the Vive Family

  Start Here

Lutron, Pico, and PowPak are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc.  
App Store is a trademark of Apple Inc., registered in the U.S. and other countries. iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Android, Google Play and the Google Play logo are trademarks of Google Inc. DALI is a trademark of ZVEI. ©2021 Lutron Electronics Co., Inc.

 A

 

On the PowPak Control Module, 
hold 

Toggle

 button “ 

u

”  for  

6 seconds until lights flash.
Both LEDs will begin flashing 
twice per second.

Associate Wireless Transmitters to 

PowPak Control Module with DALI 

Before beginning this step, make sure that there are no 

other PowPak modules being set up within the same 

building. It is possible that wireless transmitters from other 

systems can be incorrectly associated to this module.

1

 C

 

On the PowPak Control Module, hold the 

Toggle 

button “ 

u

”  for 6 seconds to save association. Lights 

will return to high-end and LEDs will stop flashing.

 B

 

Hold the indicated button on each transmitter for 
6 seconds. Lights will flash to show that wireless 
transmitters have been associated. LEDs also flash 
upon successful association.

Test

Link

Cal.

 D

 

Permanently install wireless transmitters  
(consult individual component installation guides  
for information).

Raise

Lower

Favorite

Set a Favorite Light Level 

(Optional)

For Pico remote controls with a 

Favorite

 Button.

 

A

  Adjust lights to desired level:

Use the 

Raise

 button “ ” or 

Lower

 button “ ” on the Pico 

remote control.

  

B

  Save favorite level:

Press and hold the 

Favorite

 button for 6 seconds. The load will 

flash 3 times to confirm that the Favorite level is saved.

3

 

  Low-End Trim

 

A

   Enter low-end trim adjustment mode:

 

   Press and hold the 

Lower

 button “

Δ

” on the fixture control for 12 seconds.

 

   The lights will flash and the bottom LED will begin flashing.

 

B

  Adjust the low-end trim:

 

   Use  the 

Raise

 button “

” and 

Lower

 button “

Δ

” on the PowPak Control Module to adjust and set 

the lights to the desired low-end (0.1 to 45%).

  

Note:

 Low-end depends on the minimum output of connected drivers or ballasts.

 C

   Save the low-end trim:

 

   Press and hold the 

Toggle

 button 

“ 

u

” 

 for 6 seconds to save setting.

 

   The bottom LED will begin flashing and then turn solid to indicate new level has been saved.

 

  High-End Trim

 

A

  Enter high-end trim adjustment mode:

 

   Press and hold the 

Raise

 button “

” on the fixture control for 12 seconds.  

The lights will flash and the top LED will begin flashing.

 

B

   Adjust the high-end trim:

 

   Use  the 

Raise

 button “

” and 

Lower

 button “

Δ

” on the PowPak Control Module to adjust and set 

the lights to the desired high-end (55 to 100%).

 C

  Save the high-end trim:

 

  Press and hold the 

Toggle

 button 

“ 

u

” 

 for 6 seconds to save setting. 

The load status LED will begin flashing and then turn solid to indicate new level has been saved. 

Set Low-End Trim and High-End Trim 

(Optional)

For best results, minimize the amount of sunlight entering the  
room before performing the following procedures.

 

  

Notes

  

Depending on the fixture manufacturer or load, low-end trim and high-end trim may 

need to be adjusted.

 

•   Trim low-end to ensure a stable light level because some loads will flicker or drop out 

if trimmed too low.

 

•   Be sure that you can turn on the lights to the low-end trim level without any abnormal 

operation.

 

•   The factory default high-end trim is suitable for most applications but can be adjusted 

as desired.

4

5

Set Minimum Light Level 

(Optional)

Certain applications (e.g., hallways), may require that the lights never turn off. For these areas, 
activate Minimum Light Level mode.

 

A

  Enter minimum light level adjustment mode:

Press and hold 

Toggle

 button “ 

u

”  and 

Lower

 button “

Δ

” for 12 seconds. Lights will flash 

high-low-high and both LEDs will begin flashing.
If lights stop flashing and turn off, the minimum light level is set to OFF (default).
If lights stop flashing and go to low-end, the minimum light level is ON and set to low-end.

 

B

  Change the minimum light level:

Press 

Raise

 button 

 

”  to set minimum light level to low-end.

Press 

Lower

 button “

Δ

” to set minimum light level to OFF.

 

C

  Save the minimum light level:

Press and hold 

Toggle

 button “ 

u

”  for 6 seconds. Both LEDs will quickly flash to indicate that the 

new level has been saved.

6

Set Occupancy Light Levels 

(Optional)

Note:

 Unoccupied light level is always the minimum light level and cannot be adjusted.

 

A

  Set desired occupancy light levels:

Use the 

Raise

/

Lower

 buttons 

 

  /

Δ

” on the PowPak Control Modules or the 

Raise

/

Lower

 

buttons “   / ” on associated Pico Remote Controls to adjust lights to the desired level.
Note: Setting lights to OFF during this step will make that control module unaffected by occupancy 
(will function as vacancy only).

 

B

  Save occupancy light levels:

Press and hold 

Test

 button for 6 seconds on any associated Radio Powr Savr Occupancy Sensor 

without a 

Lights On

 button. Release when Sensor lens starts to flash.

Limited Warranty

:

 www.lutron.com/en-US/ResourceLibrary/warranty/Limited%20Comm.pdf

Calibrate the Radio Powr Savr Daylight Sensor 

Daylight Sensor will control all wired fixtures equally.

 

A

  Press and release the “Cal.” button on the Daylight Sensor.

 

B

  Set lights in room to desired light level.

 

C

  Press and hold the “Cal.” button for 6 seconds.

 

D

  Exit room for 5 minutes to complete calibration.

Note:

 When calibration has completed, all lights will flash and begin to respond to daylight.

Multiple Daylight Rows

 (Optional)

For every row of daylighting a separate PowPak Control Module must be used. For detailed setup 
refer to the tuning section of the Radio Powr Savr Daylight Sensor installation guide.

 

•  Select the PowPak Control Module that you want to adjust by pressing the Toggle button.

Test

Link

Cal.

2

Reset Factory Defaults

Note:

 In some instances, it may be necessary to reset the 

PowPak Control Module with DALI and connected devices 

back to factory default settings. Before beginning, make sure 

that all devices are connected and powered.

 

A

  Triple-tap the 

Toggle

 button “ 

u

”  on the PowPak Control 

Module and hold until both LEDs begin to flash slowly; 

release button.

 

B

  Within 3 seconds of the start of flashing, triple-tap the same 

button again and the LEDs will flash rapidly indicating that the 

unit has been reset to factory defaults.

Note:

 Any associations or programming previously set 

up with the PowPak will be erased and will need to be 

re-programmed.

Customer Assistance:

India: +91.124.439.0130
Other Countries: +1.610.282.3800

www.lutron.com/support

Customer Assistance   www.lutron.com/support

     

Hereby, Lutron Electronics Co., Inc. declares that the radio equipment type RMNS-DAL32-SZ and RMNS-DAL4-SZ is in 
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.lutron.com/cedoc

Reviews: