manualshive.com logo in svg

Lutron Electronics SIVOIA, Installation And Operating Instructions Manual

Share
Download
Lutron Electronics SIVOIA Installation And Operating Instructions Manual Download Page 14

P R O B L E M

S O L U T I O N

The draperies will not open or close.

1. Check power to the motor unit by pressing the MODE

button. If the LED display does not show 
oL check that:
•  transformer has power
•

MDU is wired correctly

•

power wiring terminal is not miswired or 
disconnected

2. Try to open and close the drapery using the buttons

marked open and close on the motor drive unit. If the
drapery does not respond, check for and clear all
obstructions.

3. Check that the Open and Close limits are set correctly.

The Drapery does not respond to keypads or IR.

1. Check that power is connected to the drapery.

2. Check that MDU terminal block is connected securely

and wired correctly.

3. If using wall keypad, check that wall keypad has been

wired correctly.

4. If using IR remote, confirm that SV-IR, infrared receiver

is wired to MDU correctly, and is not obstructed.

5. If using IR remote, check transmitter batteries.

Draperies do not move together in a group

1. Confirm that all MDUs are wired correctly, including

power and Comm Link.

2. Confirm that each MDU has a unique link address, and

a common room address.

3. Confirm that keypad is a group keypad.

Drapery will not move to full open or full close

1. Confirm that open and close limits are set correctly.

2. Confirm that drapery fabric is not obstructed or caught

on something.

3. Confirm that drapery fabric is hanging from only the 1st

and 4th holes of the master car.

14

9

Troubleshooting

Sivoia

®

Drapery

Summary of Contents for SIVOIA

















Reviews:

No comments

Brands by name

Popular brands

Load more brands