ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
• Set a favorite light level
• Set high-end and low-end trim for all fixtures
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 USA
)
Lutron, Lutron, Pico, PowPak, EcoSystem, and Energi TriPak are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
©2014 – 2015 Lutron Electronics Co., Inc.
Reset Factory Defaults
Note:
In some instances, it may be necessary to reset
the fi xture controls and connected devices back to
factory default settings. Before beginning, make sure
that all devices are connected and powered.
A
Rapidly tap the
Toggle
button “ ” on the fi xture
control three times and hold on the fourth until the
LED begins to flash slowly; release button.
B
Within 3 seconds of the start of flashing, again rapidly
tap the
Toggle
button “ ” three times and the LEDs
will flash rapidly indicating that the unit has been reset
to factory defaults.
Note:
Any associations or programming previously set
up with the fi xture control will be erased and will need
to be re-programmed.
Raise
Lower
Favorite
FCC Information
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly
approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Set a Favorite Light Level
(Optional)
For Pico
®
wireless controls with a
Favorite
Button.
PowPak
®
Fixture Controls
Programming
Part of the Energi TriPak
®
Family
A
Adjust lights to desired level:
Use the
Raise
button “ ”
or
Lower
button “ ” on
the Pico
®
wireless control.
041485
Rev. A
04/2015
B
Save favorite level:
Press and hold the
Favorite
button for 6 seconds.
The load will flash 3 times to
confirm that the Favorite level
is saved.
Limited Warranty
:
http://www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf
Low-End Trim
A
Enter low-end trim adjustment mode:
Press and hold the
Lower
button “ ” on the fixture control for 12 seconds.
The lights will flash and the load status LED will begin flashing.
B
Adjust the low-end trim:
Use the
Raise
button “ ” and
Lower
button “ ” on the fixture control to adjust and
set the lights to the desired low-end (1 to 45%).
C
Save the low-end trim:
Press and hold the
Toggle
button “ ” for 6 seconds to save setting.
The load status LED will begin flashing and then turn solid to indicate new level has
been saved.
High-End Trim
A
Enter high-end trim adjustment mode:
Press and hold the
Raise
button “ ” on the fixture control for 12 seconds.
The lights will flash and the load status LED will flash.
B
Adjust the high-end trim:
Use the
Raise
button “ ” and
Lower
button “ ” on the fixture control to adjust and
set the lights to the desired high-end (55 to 100%).
C
Save the high-end trim:
Press and hold the
Toggle
button “ ” for 6 seconds to save setting.
The load status LED will begin flashing and then turn solid to indicate new level has
been saved.
Set Low-End Trim and High-End Trim
(Optional)
For best results, minimize the amount of sunlight entering the room before
performing the following procedures.
Depending on the fixture manufacturer or load, low-end trim and high-end trim
may need to be adjusted.
• Trim low-end to ensure a stable light level because some loads will flicker or drop
out if trimmed too low.
• Be sure that you can turn on the lights to the low-end trim level without any
abnormal operation.
• The factory default high-end trim is suitable for most applications but can be
adjusted as desired.
1
Troubleshooting
www.lutron.com
Symptom
Solution
Ballasts / drivers cannot
be controlled locally from
the fi xture control.
• Ensure that the breaker(s) to the fixture control are energized.
• Ensure that the fixture control switched hot lead is wired to the ballast / driver (FCJ-010).
• Ensure that the fixture control control lines (FCJ-010: violet/gray, FCJ-ECO: violet/violet) are wired
to the ballast / driver.
• If using FCJ-010, verify the driver/ballast is 0–10 V.
If using FCJ-ECO, use the Lutron
R
EcoSystem
R
driver/ballast.
Reset to factory defaults.
Lights do not dim or turn
ON as expected.
• Ensure that control lines are wired properly (FCJ-010: violet/gray-polarity-sensitive,
FCJ-ECO: violet/violet)
• Ensure that the wires are connected between the fixture sensor and the fi xture control.
• FCJ-010 only: Make sure that 0–10 V
-
fixture is at low-end (at 0 V), not OFF (at 0 V).
If OFF (at 0 V), adjust low-end trim.
• FCJ-010 only: Ensure that fixture does not require an inverted signal (10 – 0 V
-
control).
• FCJ-010 only: Verify that the voltage across the gray and violet wires is between 0 and 10 V
-
.
• FCJ-ECO only: Disconnect the violet / violet wires from the fixture control. Verify that the lights go to
100%.
• FCJ-010 only: Disconnect the violet / gray wires from the fixture control. Verify that the lights go to
100%. Short the violet / gray wires on the ballast / driver, verify that the lights go to low-end.
Lights do not respond to
wireless transmitter(s).
• Ensure that the breaker(s) to the fixture control and ballasts / drivers are energized.
• Ensure that wireless transmitters are associated to the fixture control.
Reset to factory defaults.
Wireless transmitter(s)
cannot be associated to
the fixture control.
• The maximum number of wireless transmitters have been associated to the fixture control. To
remove a previously set up wireless transmitter, tap any button on the wireless transmitter three
times; on the third tap, hold for three seconds and then tap three more times.
RF range between
wireless controls is
diminished below 30 ft
(9 m).
• Keep the ballast/driver wiring as short as possible and well organized to avoid excess wire being
bunched up.
• Keep the first 7-12 in (20-30 cm) of the wires coming out of the fixture control knockout separated
as much as possible from any nearby ballast/driver/lamp wires.
• Contact Lutron
R
technical support for further assistance.
Lights are unstable at
low-end.
• Adjust low-end trim.
Fixture sensor does not
turn the lights ON.
• Check that fixture sensor wires are connected to fixture control.
• FC-VSENSOR is vacancy only (it will not turn the lights on).
FCJ-ECO cannot be
addressed.
• All drivers/ballasts connected to an FCJ-ECO function as a single zone. If more than one zone is
required, use RMJ-ECO32-DV-B.
For more information on the PowPak
R
fixture sensor, see Document 369866 or 048556 on www.lutron.com
For FC-SENSOR and FC-VSENSOR installation guide visit www.lutron.com
NOTE:
High-end and low-end trim can also
be performed for a single unit or group of
units simultaneously with a Pico
R
wireless
control.
For more information see document 048556
on www.lutron.com.
Technical Assistance | 1.800.523.9466
USA, Canada, and the Caribbean
| +44.(0)20.7702.0657
Europe
| +1.610.282.3800
Others
| www.lutron.com
2
Start Here
