®
ODMX-512
DMX512 Input Interface (Class 2 Device) 24 V
-
100 mA
For Lutron GRAFIK 5000
T
, GRAFIK 6000
R
, GRAFIK 7000
T
,
and LCP128
T
Lighting Control Systems
Installation Instructions
Please Leave for Occupant
Description
The ODMX-512 Interface Control provides an
interface between a DMX512/1990 compatible stage
lighting console (provided by others) and a Lutron
lighting control system. The ODMX-512 will read up
to 32 consecutive DMX512 channel levels (select-
able by DIP switches). The ODMX-512 also contains
terminals that allow an external switch to be used as
an input to the lighting control system.
Important Notes:
1.
Read all instructions carefully before starting
installation.
2.
Install in accordance with all national and local
electrical codes.
3.
Turn power
OFF
at the control panel
BEFORE
installing controls.
DO NOT
connect high-voltage
power to low-voltage terminals. Improper wiring
can result in personal injury or damage to the
control and other equipment.
4.
Check with your local electrical inspector for
compliance with local codes and wiring practices.
Installation
1.
Prewiring:
The Control Links require special wiring
considerations. Refer to your lighting control system
Installation Guide and/or Lutron job drawings for wir-
ing restrictions that may apply to your specifi c project.
2.
Turn power OFF to the lighting control system.
!
WARNING: Shock Hazard. Always turn off the
power to the control panel before doing any work.
Failure to do so can result in death or serious
personal injury and/or damage to the equipment.
3.
Mount the ODMX-512 Interface to a junction box or to
a wall as shown. If the unit is not mounted to a metal
junction box, ensure proper grounding of the metal
casing by connecting a ground wire to the ground
screw. Unscrew and remove the front enclosure cover
to expose the terminal blocks, DIP Switch, and Output
Status LEDs. Insert wires through side knockouts only.
4. Assign Addresses:
Address all controls on the
Control Link. Refer to Lutron job drawings for any
preassigned job-specifi c address for each control.
Each Control Link can support up to 32 devices. For
proper system operation, each control on a link must
have a unique address. Set DIP Switch SW1, switches
1-5 on each control to select the Link Address (see
Control Link Address Settings
on back of sheet).
Record assignments for future reference.
5.
Assign DMX 512 channels to read:
Using the unit
label as a guide, set DIP Switch (SW2 DMX Zone
Select) on the unit to the desired group of 32 DMX512
channels to read.
6.
Strip insulation from wires so 3/8 in. (9.5 mm) of bare
wire is exposed (terminals will accept up to two
#18 AWG (1.0 mm
2
) wires). If using larger wire, splice
an #18 AWG (1.0 mm
2
) to the larger wire to make the
connection.
7.
Connect Control Link wiring as shown in
Typical Control
Link Wiring Diagram
. Confi rm all connections.
8.
Connect external equipment to the DMX512 Input
terminals as shown in the
Typical Interface Wiring
Diagram
.
9.
Replace front enclosure cover. Restore power to the
control panel
AFTER
the installation of the system is
complete.
MUX LINK
1
2
3
4
5
6
1 2 3 4 5
LUTRON
LED1 LED 2
Output
Status
LEDs
OMX
Control Link
DIP Switch
Control Link
Address
Input from
DMX512
channels
Ground
Screw
CONTR OL LINK
LINK
COM
+V
MU
X
MU
X
1 2 3 4
DMX 512 INPUT
+
CO M
1 2 3
-
5 6
EXT SW
EXT SW
DMX 512 INPUT
+
CO M
1 2 3
-
1 2 3 4 5
SW1
SW2
D IP Switch
DMX Zone
Select
To External Switch
(by others)
OMX-RS232
3/97 P/N 500-8521 Re
vA
INTERFACE CONTROL
SELV (CLASS 2: USA)
COOPERSBURG, PA
18036
ODMX-512
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1-32
17-48
33-64
49-80
65-96
81-112
97-128
113-144
129-160
145-176
161-192
177-208
193-224
209-240
225-256
241-272
257-288
273-304
289-320
305-336
321-352
337-368
353-384
369-400
385-416
401-432
417-448
433-464
449-480
465-496
481-512
497-512
1 2 3 4 5
1 2 3 4 5
SW 1
SW 2
Control Link Address
See Instr uction Sheet fo r Settings
DMX Zone Select
See Belo w
W
A
L
L
ODMX-512
4 in X 4 in
JUNCTION BOX
INSERT LOW-VOLTAGE
WIRES THROUGH
KNOCK OUTS
ODMX-512
W
A
L
L
