Warranty
Lutron will, at its option, repair or replace any control that is defective in materials or
manufacture within one year after the purchase. For warranty service, return unit to
place of purchase or mail to Lutron at 7200 Suter Road, Coopersburg, PA 18036-1299,
postage prepaid.
This warranty is in lieu of all other warranties, express or implied, and the implied
warranty of merchantability is limited to one year from purchase. This warranty
does not cover the cost of installation, removal, or reinstallation, or damage
resulting from misuse, abuse, or improper wiring or installation.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. Some states do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty
may last, so the above limitations and exclusions may not apply to you.
Worldwide Technical and Sales
Assistance
If you have questions concerning the installation or
operation of this product, call the
Lutron Technical
Assistance Hotline. Please provide exact model
number when calling.
(800) 523-9466 (U.S.A., Canada, and the Caribbean)
Other countries call (610) 282-3800
Fax (610) 282-3090
Remove inner
side sections
(shaded) only.
Do not remove
outer side
sections.
Figure F. Removing Side Sections
Ganging
Nova T switches can be ganged without breaking
off side sections. The Nova T design also allows
for break-offs to conserve space. See Table A or B
for the number of wallboxes you need.
When ganging any combination of small and large
controls, place all small controls at one end of gang,
all large controls at other end.
Note: When ganging with a NT-2000 control, side
sections should
not be removed on any control. See
the NT-2000 instruction sheet for appropriate wallbox
requirements.
* Note: When ganging an even number of small controls without
removing side sections, you need an additional wallbox 3/4" from
the other wallbox(es). Use a chase nipple as a spacer. See
Figure E.
Number of Small Controls
0
1
2
3
4
5
6
0
0
1
1+1*
4
4+1*
7
7+1*
Number
1
1
3
5
6
8
9
11
of Large
2
4
6
7
9
10
12
13
Controls
3
6
8
10
11
13
14
16
4
9
11
12
14
15
17
18
Table A. Wallbox Requirement Chart -
No Side Sections Removed
Number of Small Controls
0
1
2
3
4
5
6
0
0
1
2
3
4
5
6
Number
1
1
3
4
5
6
7
8
of Large
2
3
5
6
7
8
9
10
Controls
3
5
7
8
9
10
11
12
4
7
9
10
11
12
13
14
Removing Side Sections
Remove only inner side sections. Do not remove
outer side sections on ends of gang. Using pliers,
bend side sections up and down until they break off.
Four-gang
gangable wallbox
3/4" space
(use chase
nipple)
Single-gang
gangable
wallbox
Figure E. Four-Gang Installation -
No Side Sections Removed
Table B. Wallbox Requirement Chart -
Side Sections Removed
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in U.S.A. 6/99 P/N 030-606 Rev. A
Cutting Plastic Faceplates
Some faceplates will need to be cut if removing side
sections of dimmers and not using a multigang
faceplate.
To cut faceplates:
1.
Position faceplate face down on soft cloth.
2.
Press firmly and score groove on back of
faceplate with razor-sharp knife. Use vertical
side of groove to keep knife on straight course
(see Figure G).
3.
Bend section back and forth several times to
break it off. Do not use pliers.
4.
Smooth edges by placing fine-grained sandpaper
on flat surface and rubbing edge of faceplate
over it a few times. Hold faceplate steady as you
rub to keep edge true.
Figure G. Cutting Faceplate
