0-10 Warm Dim 96 watt LED Driver
-
Installation Instructions
Models PS010WD-96-24
Please read all instructions prior to installation and keep for future reference!
2
2.1
Remove the eight Phillips screws from the top of the driver
housing and pull the cover off to expose the driver wires.
housing
cover
Phillips screw
2.1
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
24V DC, 4.0A
Max. wattage
96 W
1
1.1
LED Driver can be mounted vertically or horizontally. With a
minimum of 2" clearance around LED Driver to provide proper
air circulation.
Before installing, check the label and ensure the LED
Driver has the proper input voltage, output voltage, and
wattage for the job. Check the wire markings to ensure
they match the wiring diagram below. Refer to table
above for the maximum loads!
2” min.
2” min.
2” min.
5.2”
2.6”
13.4”
14.4”
Input
120 - 277V AC, 1.1A, 50/60Hz
Output
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
REV0.5 11152018
This LED Driver is to be installed in accordance with Article 450 of the National Electrical Code. The LED Driver must be
installed in a well ventilated area and free from explosive gases and vapors. Proper operation requires the free flow of air. As
this LED Driver is hardwired, it should only be installed by a qualified electrician. Suitable For Damp Location.
3
3.1
Connect the 120-277V AC
power into the housing from
the electrical panel. Followed
by connecting the 24V DC
low voltage conduit, one for
the LED & other for the
controller wires. Refer to the
diagram below to make all
the proper wiring
connections.
L
N
GRD
gray-
Vin1-
black
Vin1+
red
warm+
yellow
warm-
blue
cool-
blue
cool+
yellow
Vin2-
black
Vin2+
red
-
+
120 - 277V AC
SLD-DIM-TW
Tunable white LED PWM dimming module
Dimming range: 0-100%
0/1-10V control, 0/1V=0% light output
10V=100% light output
PWM Output to LED Modules (8-48V PWM, 1K Hz)
For use with Class 2 DC LED Driver only
connect
to 24VDC
connect to 0-10V
controller wires
LED Driver 96W max
LLDW52 Dynamic white
+
+
reference LineLED wire lead
labels to determine polorarity
connect
to 24VDC
reference LineLED wire lead
labels to determine polorarity
Wiring diagram connecting
to LLDW36 LineLED
gray-
Vin1-
black
Vin1+
red
warm+
yellow
warm-
blue
cool-
blue
cool+
yellow
Vin2-
black
Vin2+
red
SLD-DIM-TW
Tunable white LED PWM dimming module
Dimming range: 0-100%
0/1-10V control, 0/1V=0% light output
10V=100% light output
PWM Output to LED Modules (8-48V PWM, 1K Hz)
For use with Class 2 DC LED Driver only
connect to 0-10V
controller wires
+
-
-
WW
CW
L
N
GRD
-
+
120 - 277V AC
LED Driver 96W max
PS010WD-96-24 power supply
connect
to 24VDC
reference LineLED wire lead
labels to determine polorarity
LLDW36 Dynamic white
Wiring diagram connecting
to LLDW52 LineLED
PS010WD-96-24 power supply
Page 1 of 2
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
