F.H.Papenmeier GmbH & Co. KG · division Lumiglas
Talweg 2 · 58239 Schwerte · GERMANY
phone: +49 2304 205-0 · fax: +49 2304 205-206
[email protected] · www.lumiglas.de
®
All dimensions in mm unless stated otherwise. Subject to change without prior notice.
WW 02.09 3755.157
Important guidelines for mounting and use of
sight glass fittings, toughened glasses and luminaires:
Before installation and operation/servicing, please read and follow all commissioning and servicing instructions.
1.
Installation of sight glass fittings
The installation by welding, brazing etc, must be free of distortion
and thus carried out by suitably qualified and authorized personnel.
2.
Installing toughened glass discs into a sight glass assembly
2.1 Operating safety of sight glasses depends to a great extent upon their
correct installation.
2.2 The gasket seating surfaces in the flanges must be plane, flat and
smooth. Ensure the gasket edges are not trapped by, or foul, the
flange gasket recess wall.
2.3 The glass disc, with gaskets appropriate to the process application
fitted to its top and bottom faces must be located concentrically in
the flange assembly.
2.4 Only use gaskets which are in good condition, flat and free of dirt
and grease.
2.5 Before tightening nuts or bolts ensure once more that cover and base
flanges are correctly aligned and surfaces parallel to one another.
2.6 Tighten the nuts or bolts progressively in diametrically opposed pairs.
Tightening moments can be obtained from the relevant data sheets
accompanying product (or consult supplier).
2.7 Further tightening down may be required after assembly has bedded
down under operating temperature and pressure.
2.8 When installing quartz sight glass discs follow manufacturers’
instructions!
3.
Max. loading of toughened sight glass discs
3.1 Correctly fitted sight glass discs must be used within the working
temperature and pressure ranges laid down for them otherwise they
may fail.
3.2 Temperature cycling to be within permitted limits:
• Sodalime glass (DIN 8902), max permissible temperature: +150° C.
Temperature change within one minute max from 120° C to 20° C
with glass fully immersed.
• Borosilicate glass (DIN 7080), max permissible temp.: + 280° C.
Temperature change within one minute max from 230° C to 20° C
with glass fully immersed.
3.3 Avoid spraying sight glasses which are still hot with cold fluid.
Warning! This can lead to glass disc breakage.
3.4 Safety Precautions when using sight glass discs:
3.4.1 Scheduled Maintenance:
Sight glasses must be included in preventive maintenance, and
regularly checked either visually or by ultra sound measurement of
wall thickness. Where a disc shows any damage it must be exchanged
promptly with the plant shut down. Further, a thorough and regular
check of the sight glass should lead to a down time to suit the
par ticular vessel; this will promote a routine for glass exchange suited
to the process.
3.4.2 Breakage of glass disc:
In spite of careful fitting and operation in accordance with instruc-
tions, it is possible though rare, that due to external effects a glass
disc can fail. It is necessary, particularly in the case of critical processes
such as in the food industry, that the plant manufacturer or operator
takes appropriate safety measures to prevent glass fragments finding
their way into the product.
3.5 After dismantling a sight glass assembly, and in accordance with
DIN 7080 standard requirements for all type of sight glass disc, the
glass disc and gaskets are replaced with new ones before the
assembly is put back into operation. This is particularly important
where pressure vessels and/or aggressive media are concerned.
The following wording as extracted from DIN 7080 refers:
“Sight glass discs may only be installed by personnel who are
thoroughly versed about the following requirements:
• careful treatment of sight glass discs
• cleaning of recesses, discs, gaskets and accessories prior to installa-
tion, i. e. the removal of foreign matter (e. g. machining swarf);
• even tightening up of holding down bolts.
Sight glass discs removed from assemblies following operational
service may not be reused.”
4.
Sight glass wiper
4.1 Check that wiper assembly is correctly installed (see separate
installa tion instruction)!
4.2 Wipers may only be used within temperature and pressure ranges
specified.
4.3 Drive/spindle housing should be periodically checked to ensure a good
seal; if necessary tighten threaded bushes/glands, replace defective
seals, clean wiper arms and blades to remove accumulated foreign
matter or replace (see installation instruction).
5.
Spray device
The spray fluid temperature should be as near as possible to that of
vessel contents. On no account use cold spray fluid on hot glass disc
(see ‚temperature cycling‘ under point 3).
6.
Sight glass luminaires
6.1 Always ensure that luminaire is connected to correct supply voltage as
indicated on identity plate.
6.2 All luminaires are purpose designed and exclusively made for moun-
ting onto flanged sight glass assemblies.
6.3 Never use the luminaire in place of cover flange or a complete sight
glass fitting.
6.4 Only certain models of luminaire may be used in con tinuous ON
mode; please check before confirming order; if in doubt ask supplier
or manufacturer.
6.5 Luminaires with built in ‚non maintained‘ switches are for intermit-
tent use and may only be operated with those switches.
6.6 Luminaires intended by the user for continuous ‚ON‘ mode operation
should be controlled by separate external ON/OFF switch.
6.7 The following should also be noted
• Max. permissible temperature at cable entry not to be exceeded
(see data sheet).
• Max. permissible temperature of glass not to be ex ceeded (Vessel
tempe temperature increase caused by luminaire =
sight glass temperature; check by measurement!)
6.8. When replacing lamps use identical type with identical power rating;
never exceed max. permissible lamp rating recommended for any
given luminaire.
6.9 When changing lamps, check condition of lamp socket as a matter
of course.
6.10 Excessive voltage will shorten lamp life.
7.
Ex Hazardous areas
Ex hazard rated luminaires must not be installed or serviced other
than by suitably qualified and authorised personnel. Data and
instructions contained in relevant approval test certificates (certifi-
cates of conformity) must be adhered to. Some Ex luminaire models
are works fitted with permanently encapsulated (resin cast) cable
tails; on no account attempt to unscrew or remove cable entry gland!
Any inappropriate change in components of Ex certified luminaires
can render the relevant certificate invalid.
8. Hinged or screwed sight glass assemblies
Before use, ensure the seals are functioning (if necessary tighten
securing nuts/bolts).
The seal between hinged ports and vessel flange is en sured by
correctly seated components; flanges to mate up parallel by correctly
adjusted swing-bolt/hinge assembly and undamaged, clean seals free
of grease.
In the case of hinged units, ensure the material of the hinged glass
serround is compatible with vessel contents. When used on pressure
vessels, ensure max. operating pressure specified for the sight glass is
exceeded.
If in doubt, consult supplier or manufacturer!
Sales: Malux Finland Oy, P.O.Box 69, FI-06151 Porvoo, Phone +358 19 574 5700, Fax +358 19 574 5750, [email protected]