manualshive.com logo in svg

Lucky Star 5V-1B, User Manual

Share
Download
Lucky Star 5V-1B User Manual Download Page 29

         5V-1B

                                                Page

25

Disabled

:  disable cache

Quick Power On Self Test

This category speeds up power on self test.  After you power on
the computer, if it is set to enable, during post.
Enabled : 

  BIOS will shorten or skip some check items.

Disabled:

   normal speed

Boot sequence

This category determines which drive the system searches first.
Take “ A,C,SCSI”

 for example. System will first search for

floppy disk drive; second is hard disk drive, and finally SCSI
drive.  Default value is 

“ A,C,SCSI.” .

  Options are as below:

A,C,SCSI; C,A,SCCI, C,CDROM,A; CDROM,C,A; D,A,SCSI;
E,A,SCSI; F,A,SCSI; SCSI,A,C; SCSI,C,A; C Only ; LS/ZIP,C.

Swap Floppy  Drive
Enabled: 

 floppy A&B will be swapped.

Disabled

(default):  floppy A&B will be not swapped.

Boot Up Floppy  Seek

BIOS will determine if the floppy disk drive is 40 or 80 tracks
360k type is 40 tracks while 720K/ 1.2M  and 1.44M are all 80
tracks.  Default value is 

enabled.

Boot Up Numlock Status:
:On(default)
:Off

Boot Up Sy stem Speed

It selects the default system speed which the system will run
immediately after power up.
High(default): set the speed to high.
Low:  set the speed to low.

Gate A20 Speed
:Normal (default)

Summary of Contents for 5V-1B





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands