LUCHT LHZ Technotherm TTB-E Duo 08 Manual Installation Download Page 3

FEEL GOOD THROUGH THE WARMTH FROM ELECTRICITY - www.technotherm.de

FEEL GOOD THROUGH THE WARMTH FROM ELECTRICITY - www.technotherm.de

3

|

Manual: TTB-E Duo+

GB

Do not install electric storage heaters in rooms 

where contact with fl ammable or explosive mate-

rials like dust, gas or vapour cannot be avoided. 

This refers also to a short � me usage of the heater 

while any kind of fl oor covering work is done, and 

where  dust  is  created  or  gas  or  fl ammable  pro-

ducts are used. In any of these circumstances the 

heater should not be charged and must be cover-

ed, especially at the air outlet grille. For installa� -

on in commercial buildings (e.g. workshop, hair-

dressing salon, laboratories, etc.), please contact 

your professional associa� on.

To prevent accidents and possible � pping of the 

heater,  it  must  be  fi xed  to  the  wall  with  safety 

screws, supplied with the heater. The necessary 

screws and plugs are found in the lower part of 

the switchboard in a plas� c bag.

If the wall is not strong enough a more adequate 

fi xing material has to be used.

Installa� on

For safety against � pping fi x the rear chimney pa-

nel (4) with appropriate screws and plugs to the 

wall.

Fix the drill holes and the plugs according to the 

instruc� ons in fi g. 1 and fi g. 2 and the type of ap-

pliance.

For this purpose, loosen two screws (8) on the 

rear panel, take the rear chimney panel (4) away 

and fi x it horizontally to the wall. At least two of 

the moun� ng holes (9) must be used (see fi g. 2 

and table 1).

A� er making sure the rear chimney panel is pro-

perly  fi xed  to  the  wall,  the  appliance  can  be 

suspended in the rear panel slot.

Important

The fi xing to the wall of the rear chimney panel is 

done exclusively for  safety against � pping. Note 

that the appliances are only  suitable for wall 

moun� ng above the  fl oor if wall consoles or al-

ready available runners are used.

Important

When the appliance is fi lled with bricks, it may sink 

somewhat into the pile when placed on thick-pile

carpe� ng.

Maintenance

Clean the heater, preferably when it is cold, with 

a humid cloth and a� erwards with a so�  dry rag. 

Do not use any fl ammable or abrasive products to 

clean the heater.

The cleaning should be done regularly in order to 

prevent any  permanent  stains on the heater due 

to dust parts burning or par� cles glued to the pa-

nels.

Moun� ng instruc� on, reserved to the professional

installer

Place

Please follow the safety guidelines for installa� on, 

security and load bearing capacity men� oned in 

this manual. In case of doubt concerning the fl oor 

resistance, seek the advice of an architect.

The  stability  of  the  appliance  must  be  guaran-

teed: place the appliance on a fl at surface. For a 

correct func� onality, avoid placing the heater on 

a carpeted or � led fl oor which is not even and/or 

completely horizontal.

Summary of Contents for Technotherm TTB-E Duo 08

























Reviews: