ON
MSG
RANGE
BATT
PSTAT
18
1
8
2 3
7
6
5
4
-Handset Display-
Your MDC 9000 or MDW 9000/9010 Telephone
1 — Line Status Indicators
show status of
outside and inside lines. Arrow or rectangle
“points” to the line button it represents and
flashes in different patterns to show activity
on the line (see box below).
2 — P
appears when in program mode.
3 — STAT
(MDC 9000 only) appears steady-on
when handset is out of range. Remains until
all line status indicators are updated.
MUTE
(MDW 9000/9010 only) appears when
the handset microphone is off.
4 — MSG
appears when you have received a voice
mail message.
5 — BATT
appears when there are only a few
minutes of conversation time left. Handset
gives 2 short beeps. Place handset on the
base to recharge.
6 — RANGE
appears (and handset beeps twice)
if
Status
(off only) or
On/Off
button is
depressed when handset is out of the base’s
range. To make or receive calls, move
handset closer to base.
7 — ON
appears when the handset is turned on
after you pressed
On/Off
.
8 — 18
(MDW 9010 only) indicates Local Test
Mode;
1
through
10
are used in Wireless
Test Mode.
To Update Display:
Press
Two Loud Beeps
means:
Move Closer to Base Unit
Status
ON
MSG
RANGE
BATT
PSTAT
Status
On/Off
Hold
2
ABC
3
DEF
1
6
MNO
9
WXYZ
#
5
JKL
8
PQRS
0
Oper
4
GHI
7
*
Conf
Trans
Feat
TUV
Ext.
1 6
MDC 9000
STAT/RANGE
means:
Move Closer to Base Unit
User Instructions
(MDC 9000) A quick reference
to most important cordless
phone features.
Directory Card
(MDC 9000, behind cover)
Antenna
Headset Jack
(MDC 9000) For headset adapter
cord.
Battery Charging
Contacts
Handset batteries charge through
these contacts. Clean periodically
by rubbing them with a soft gum
eraser.
Status
(MDC 9000) Press to turn on the
display when the handset is off,
or to update the display when the
STAT
indicator appears.
Volume Control
(MDC 9000) Slide the switch to
adjust the volume of the earpiece to
Normal
or
High
.
(MDW 9000/9010) An 8-interval
pushbutton controls the ringer
volume when the phone is off and
the receiver volume when the
phone is on.
Mute
(MDW 9000/9010) Press to turn
the microphone on/off so that
you can/cannot be heard by the
caller.
Conf (Conference)
Press to add another party to
your call (see p. 7).
Headset Jack
(MDW 9000/9010) For headset
adapter cord.
Feat (Feature)
Press to enter program mode
(see p. 22).
Handset Extension
Label
Write the extension number
on this label using a pencil
or ballpoint pen only.
Trans (Transfer)
Press to transfer a call to
another extension (see p. 7).
Handset Display
Displays status of lines and
range. For details, see figure
opposite.
Outside Line/
Programmable/
Intercom/ Drop
Buttons (6)
See
p. 3, for line button
assignments.
Hold
Press to put a call on hold
(see p. 7).
On/Off
To turn the handset on, press
once.
ON
appears in the
display. To turn off, press
again. Turn on to make or an-
swer a call, and turn off to hang
up (see p. 7).
1
Flash
Long on, long off indicates a ringing call.
Wink
Long on, short off indicates a call on hold.
indicates the line you’re using.
-
Line Status Indicators
-
Arrows
(
