Lucent Technologies CAJUN M770 User Manual Download Page 157

Page: 157 / 266

Chapter 11

Managing the Management LEC

Cajun M770 ATM Switch User’s Guide

139

The data plane information for the

lane lec statistics

command is shown in

Table 11.3.

Table 11.3

Output from the lane lec statistics command (data plane)

Field

Description

unicasts

In / Out

The number of data frames received and sent to a
single destination.

multicasts

In / Out

The number of data frames received and sent to a
group MAC address.

broadcasts

In / Out

The number of data frames received and sent to all
MAC addresses.

packets sent to
BUS

The number of packets sent to the BUS by the management
LEC.

BUS packets
discarded

The number of packets sent to the BUS that have been
discarded.

errors

The number of data frames discarded, for example, due to
an unrecognised MAC address or an illegal data format.

Out

The number of oversize data frames that have been
discarded.

unknown
protocols

The number of data frames received for unassigned Link Layer
Control (LLC) protocols.

raw data
(bytes)

In/Out

The total number of data bytes received and sent.

Summary of Contents for CAJUN M770











































































































































































































































































Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands

Lucent Technologies CAJUN M770, User Manual

Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands