background image

Zhengzhou Linghang Robot Co.,Ltd

4

1. Safety

This section describes the general safety guidelines to be followed for this

product

The mentioned warning instructions and safety precautions are

applicable to this product. Refer to other application manuals for more specific
warning instructions.
1.1 Notices:

The following notice is for the products covered by this manual. Users should

pay attention to all notifications from robot manufacturers and robot parts
manufacturers.

Danger: inform information or instructions that failure to comply
will result in death or serious injury. The Notice provides
information on the nature of the dangerous situation, the

consequences of not avoiding the danger and the methods to avoid it.

Warning: Notice of information or instructions that may result in
death or serious injury if not observed. The notification provides
information on the nature of the hazardous situation, the

consequences of not avoiding the hazard and the methods to avoid it.

Note: inform information or instructions that failure to comply may
result in moderate injury or equipment damage. The notification
provides information on the nature of the hazardous situation, the
consequences of not avoiding the hazard and the methods to avoid

it.

Notice: Notice of specific information or instructions for maintaining, operating,
installing or setting up the product. Failure to follow these information or
instructions may cause equipment damage. The notice emphasizes, but is not limited
to, specific grease types, best operating practices, and maintenance techniques.

Summary of Contents for LTC-0005A








































Reviews: