background image

Nut

 2 / 3             

 

    p/n 442652 

    Rev.  1/11

LSI Industries Inc.     10000 Alliance Road       Cincinnati, Ohio 45242       (513) 793-3200        Fax (513) 793-0147        www.lsi-industries.com

©2011 LSI Industries Inc.

442652   Rev. 1/11   

 

 

 

 

 

 1 / 3

LSI Industries Inc.       10000 Alliance Road       Cincinnati, Ohio 45242       (513) 793-3200        Fax (513) 793-0147      www.lsi-industries.com

 

    Listed to UL1598
   Canopy Luminaire,
Suitable for wet locations
  

1

Collar

Clamp
Bracket

  DOUBLE-DECK CROSSOVER

® 

SERIES LUMINAIRE, cont'd.

 

 

 

 

 

 

 

 

        

 

 

 

 

 

 

 

 

 

Install Mounting Bracket using outer most holes in flange

 

 

 

 

 

 

 

 

 

and (4) #10-24 x 1" screws.  Tighten screws so Mounting

 

 

 

 

  

 

 

 

 

Bracket is flush and tight up against decking.

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT: The following instructions are for

 

 

 

 

 

 

 

                              

 

qualified electricians only!

        

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Locate Driver Box.  Open Driver Box Cover from bottom by

 

 

 

 

 

 

 

 

 

loosening side screw and rotating top upward. Secure box

 

 

 

 

 

 

 

 

 

bottom to conduit stem.  With (1) Stem Nut in hand -

 

 

 

 

 

 

 

 

 

locking teeth facing UP - feed both luminaire connectors

 

 

 

 

 

 

 

 

 

thru Nut, then thread nut onto Stem external threads; fully

 

 

 

 

 

 

 

 

 

thread Nut all the way down Stem until it stops.  Feed

 

 

 

 

 

 

 

 

 

all luminaire wiring thru box bottom, then lower Box

 

 

 

 

 

 

 

 

 

onto Stem.  With other Stem Nut in hand - locking teeth

 

 

 

 

 

 

 

 

 

facing DOWN - feed wiring thru nut, then thread

 

 

 

 

 

 

 

 

 

onto Stem and tighten.  Make secondary wiring

 

 

 

 

 

 

 

 

 

connections per terminal block label inside Driver Box.

2

Nut

INSTALLATION AND ASSEMBLY INSTRUCTIONS

CRR/CRR3 DOUBLE-DECK CROSSOVER

® 

SERIES LUMINAIRE

 

   

WARNING:  Failure to follow instructions could result in
 

 

       damage to product and void warranties!

 

 

       For new installations ONLY! For retrofit of existing luminaires refer

 

 

       to proper retrofit instructions!

 

 

       Risk of fire or electrical shock.  Disconnect power before installing

 

 

       or servicing.

NOTE: For installation on Metal double-deck Canopies.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Driver for

            128 LED Luminaire 

  104 LED Luminaire        84 LED Luminaire   64 LED Luminaire    Focus Luminaire        all Luminaires

  

Suggested Tools: 

Flat screwdriver, Philips screwdriver, caulk gun

 

Reference site layout for luminaire location and type.  Ensure nothing is above decking before cutting.  Cut

 

an 11" square hole in between canopy ribs.  Apply 1/4" bead of Sealant/Adhesive (supplied) around hole.

 

Push Collar up through the hole and into the Sealant/Adhesive to create a water tight seal.  Install (2) Clamp

 

Brackets by inserting them up through the hole and back down over the lip of the Collar.  Secure Clamp

 

Brackets to Collar using outer most holes in flange and (4) #10-24 x 1" screws.  Tighten screws so that Collar

 

flange is flush and tight up against decking. 

NOTE: For thin-material canopies, holes are provided at top of

 

Collar which allow wire hanging from interior canopy structure.

         

 

1/4" Bead Sealant
Adhesive (supplied)

#10-24 x 1"
       Screw

Driver
   Box

Stem

Mounting
Bracket

#10-24 x 1" Screw

Deck

Luminaire

3

 

Clamp
Bracket

Driver
Box Cover

Side
screw

Collar Holes
(for additional support
on thin canopy decks)

Reviews: