Programmable Logic Controller Installation Guide
Smart I/O XEL-BSSRT/F/H
This installation guide provides simple function information or PLC control. Please read
carefully this data sheet and manuals before using products. Especially read precautions then
handle the products properly.
■
Meaning of warning and caution label
WARNING
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury
CAUTION
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices
WARNING
①
Do not contact the terminals while the power is applied.
②
Be sure there are no foreign metallic matters.
③
Do not manipulate the battery(charge, disassemble, hitting, short, soldering).
CAUTION
①
Be sure to check the rated voltage and terminal arrangement before wiring
②
When wiring, tighten the screw of terminal block with the specified torque range
③
Do not install the flammable things on surroundings
④
Do not use the PLC in the environment of direct vibration
⑤
Except expert service staff, Do not disassemble or fix or modify the product
⑥
Use the PLC in an environment that meets the general specifications contained in
this installation guide.
⑦
Be sure that external load does not exceed the rating of output module.
⑧
When disposing of PLC and battery, treat it as industrial waste.
⑨
I/O signal or communication line shall be wired at least 100mm away from a high-
voltage cable or power line.
■
To install, observe the below conditions.
No
Item
Specification
Standard
1
Ambient temp.
0 ~ 55
℃
-
2
Storage temp.
-25 ~ 70
℃
-
3
Ambient humidity
5 ~ 95%RH, non-condensing
-
4
Storage humidity
5 ~ 95%RH, non-condensing
-
5
Vibration
Resistance
Occasional vibration
-
-
Frequency
Acceleration Amplitude
Number
IEC 61131-2
5≤f<8.4
㎐
-
3.5mm
10 times in
each
direction
for
X, Y, Z
8.4≤f≤150
㎐
9.8
㎨
(1g)
-
Continuous vibration
Frequency
Acceleration Amplitude
5≤f<8.4
㎐
-
1.75mm
8.4≤f≤150
㎐
4.9
㎨
(0.5g)
-
■
For system configuration, the following version is necessary.
1)
XG5000 Software
: V4.30 or above
■
For more information, please refer to user manual.
Item
Specification
Communication protocol
RAPIEnet, EtherNet/IP, Modbus-TCP, BOOTP, DHCP
Transmission speed
100/1000Mbps
Communication cable
Electric: S-FTP over CAT5e
Optical: Multi-mode/Single-mode fiber optic cable(MMF/SMF)
Maximum expansion stages
8 slot
Output current
3.0A
*1)
Internal current consumption
BSSRT: 710
㎃
, BSSRF: 750
㎃
, BSSRH: 730
㎃
*1)
Be careful that the sum of the current consumption does not exceed the output current.
■
This is front part of the product. Refer to each name when operating the system. For more
information, refer to user’s manual.
\
■
Parts name and function
No.
Name
Description
①
Status LED
RAPIEnet/IP Adapter operation status LED,
Network communication status LED
②
Rotary Switch
Node Address switch
③
Power connector
DC24V power input connector
④
Media connector
Media connector (electric, optical)
⑤
USB connector
USB connector to connect with XG5000
⑥
USB protection cover Protection cover for USB connector
⑦
Expansion cover
Protection cover for expansion connector
■
LED details
LED
Status
Description
RUN
Off
Power Off
Green On
Master module is RUN
Red On
Master module is STOP
Green Blink
Waiting for service
RMS
Green On
Normal
Green Blink
Devices setting is not complete
Red On
Non-restorable error occurs
Red Blink
Invalid setting, Restorable error occurs,
Parameter errors, Initialization errors,
Different speeds or duplexes between ports
RNS
Green On
At least one connection
Green Blink
Device is not connected
Red On
Duplicated IP address/station number is detected
Red Blink
Time-out occurs with one or more devices
Frame error or heartbeat error occurs
RELAY
Off
Relay Off
Green On
Relay On
LINK/ACT1
LINK/ACT2
Off
Link=No, Activity=NA
Green On
1G Link=Yes, Activity=No
Green Blink
1G Link=Yes, Activity=Yes
Yellow On
10/100M Link=Yes, Activity=No
Yellow Blink
10/100M Link=Yes, Activity=Yes
■ H
ere describes the method to attach each module to the base or remove it.
1) Attachment of product
①
When extension input/output
module is installed, pull two levers
of adapter module up.
②
Push the product and connect
it agreement with hook for fixation of
four edges and hook for connection
③
After connection, get down the hook
For fixation and fix it completely
2) Detachment of product
①
Push up the hook for disconnection.
②
Detach the product with two hands. (Don’t force it.)
7
Wiring
■
Installation of cable
1)
100/10000BASE-TX’s max.extended length between nodes is 100m.
2)
This module provides Auto Cross Over function so the user can use both cross and
straight cable.
Pin No.
Sign
Cable wiring
Straight cable
Cross cable
1
TD+
1 ----- 1
1 ----- 3
2
TD-
2 ----- 2
2 ----- 6
3
RD+
3 ----- 3
3 ----- 1
4
TRD2+
4 ----- 4
4 ----- 7
5
TRD2-
5 ----- 5
5 ----- 8
6
RD-
6 ----- 6
6 ----- 2
7
TRD3+
7 ----- 7
7 ----- 4
8
TRD3-
8 ----- 8
8 ----- 5
8
Warranty
■ Warranty period
18 months after the production date.
■ Scope of Warranty
18-month warranty is available except:
1)
The troubles caused by improper condition, environment or treatment except the
instructions of LS ELECTRIC.
2)
The troubles caused by external devices
3)
The troubles caused by remodeling or repairing based on the user’s own discretion.
4)
The troubles caused by improper usage of the product
5)
The troubles caused by the reason which exceeded the expectation from science
and technology level when LS ELECTRIC manufactured the product
6)
The troubles caused by natural disaster
■ C
hange in specifications
Product specifications are subject to change without notice due to continuous product
development and improvement.
LS ELECTRIC Co., Ltd
10310001663 V1.2 (2020.4)
•
E-mail:
•
Headquarter/Seoul Office
Tel: 82-2-2034-4033,4888,4703
•
LS ELECTRIC Shanghai Office (China)
Tel: 86-21-5237-9977
•
LS ELECTRIC (Wuxi) Co., Ltd. (Wuxi, China)
Tel: 86-510-6851-6666
•
LS-ELECTRIC Vietnam Co., Ltd. (Hanoi, Vietnam)
Tel: 84-93-631-4099
•
LS ELECTRIC Middle East FZE (Dubai, U.A.E.)
Tel: 971-4-886-5360
•
LS ELECTRIC Europe B.V. (Hoofddorf, Netherlands)
Tel: 31-20-654-1424
•
LS ELECTRIC Japan Co., Ltd. (Tokyo, Japan)
Tel: 81-3-6268-8241
•
LS ELECTRIC America Inc. (Chicago, USA)
Tel: 1-800-891-2941
•
Factory: 56, Samseong 4-gil, Mokcheon-eup, Dongnam-gu, Cheonan-si, Chungcheongnam-
do, 31226, Korea
1
Safety Precautions
2
Use of environment
3
Applicable Version
4
Performance Specifications
5
Parts name and Dimension (mm)
6
Mounting & Installation
C/N: 10310001663
