LRX SCORPION Page 14 Manual Download | Manualshive

Page: 14 / 20

background image

LRX™ SCORPION

Check on line for the latest updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

13

13

LAMP INSTALLATION



A number of hazards exist during lamp installation please refer to

safety warnings on page two.



Follow lamp manufactures instructions regarding use and handling of their

product.



This fixture has more than one power supply. Disconnect all power supplies

before installation or removal of the lamps.



Allow lamps to cool before removing.



Loosen the two screws that hold the lamp retaining ring, then rotate ring to

remove.



Prior to installing the lamp, check lamp contacts and wire ends for signs of

arcing or over-heating. If lamp contacts or wiring appear damaged remove

from service.



Ensure power supply matches lamp type, voltage and wattage.

«
...
12
13
14
15
16
...
»

Summary of Contents for SCORPION





















Reviews:

No comments

Related manuals for SCORPION

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: ParaBody Pages: 5

Brand: Sagola Pages: 20

Brand: Earmor Pages: 5

Brand: Obdstar Pages: 10

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: ICELED Pages: 4

Brand: Facom Pages: 4

Brand: FaceLake Pages: 2

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: R&S Pages: 2677

Brand: TDR Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands