manualshive.com logo in svg

Lovol 1004-4, User Handbook Manual, Page: 33 / 87

Share
Download
Lovol 1004-4 User Handbook Manual Download Page 33

                                                                                                                                                                                                                                                                                                                                               

 

 

Air elimination in fuel system of the 

fuel injection pump fitted with Bosch EPVE

 

 

1.

 

Loosen the vent plug on the top of the twin element fuel filter (A1). If a single element filter is used, loosen the 

banjo connection bolt which is fitted on the top of the filter (B1). 

2.

 

Operate  the  priming  lever  on  the  fuel  lift  pump  (C)  until  fuel,  free  from  air,  comes  from  the  filter  vent  point. 

Tighten the vent plug or the banjo connection bolt. 

Remark:

 If the drive cam of the fuel lift pump is at the point of maximum cam lift, it will not be possible to operate 

the priming lever. In this situation, the crankshaft must be turned one revolution. 

 

3.

 

Ensure that the manual stop control is in the "run" position. If an electrical stop control is used, turn the start key 

to the "R" position. 

4.

 

Loosen the vent screw of the fuel pipe (D1) of the fuel injection pump (B1). 

5.

 

Operate the priming lever of the fuel lift pump until fuel, free from air. Conies from the vent screw(s).Tighten 

the vent screw(s). 

 

 

 

 

 

 

4.13 

Summary of Contents for 1004-4
























































































Reviews:

No comments