* For reference only.
Following data for reference
DM15LEU/L-0.3/30
0.3
30
0.6
5
DM15LEU/L
A-00
-1-
-2-
Features
Built-in Receiver
Jog & Tilt
Built-in Lithium Battery
Scan and Program
Solar Charging
Switch Direction
Stall Protection
Program Button
Reset to Factory Mode
Status Feedback
Electronic Limit
Preferred Stop Position
Speed Regulation
Scene Control
Memorized Setting
Instruction
SAFETY NOTE
1, This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
2, Children shall not play with the appliance.
3, Cleaning and user maintenance shall not be made by
children without supervision.
4, If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5, WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6, The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or less
than 70 dB(A), e.g. by writing LpA
≤
70 dB(A).
7, The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8, The type of driven part the drive is intended for.
9, WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10, Do not allow children to play with fixed controls. Keep
remote controls away from children.
11, Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary.
12, Watch the moving shutter and keep people away until
he shutter is completely closed.
13, WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14, Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation.
Fields of Application
The motor is suitable for motorization of roller blinds.
Specifications
Working Temperature: -10
℃
~ +50
℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model
Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Current
(A)
Rated Power
(W)
Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Motor Installation
Drive tube
Drive tube
Step 1 Cut drive tube to required length.
Step 3 Mount correct crown & drive adapter on
the motor. Make sure drive adapter fits firmly and
crown rotates freely.
Step 4 Align the notches on the crown and drive
adapter with the drive tube, slide and fit the motor
into drive tube. Mount idler and bracket on both
ends.
Step 2 Ensure tube edge is clean and burr-free.
Bracket
Bracket
②
Drive Adapter
①
Crown
③
Circlip
Charging Instructions
Micro-USB charging: 5V
Micro-USB Port
Rechargeable Battery
This motor has a 8V built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) , or charging
with 5V solar panel.
During operation, motor will stop running when the voltage is lower than 6.5V and it will resume again when
the voltage is greater than 6.8V.
When the motor is running continuously when the voltage is lower than 7.2v, the red light will flash for 10 times
for low pressure alarm.
Blinking red
during operation;
Charge the battery
Blinking red;
battery is charging
Continuously red;
battery is fully charged
Solar (PV) Panel: 5V
R4045
Instructions
Charging Instructions
This motor has a 8V built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours using 5V charger.
During operation, motor will stop running when the voltage is lower than 6.5V and it will resume
again when the voltage is greater than 6.8V.
When the motor is running continuously when the voltage is lower than 7.2v, the green light will
flash for 10 times for low pressure alarm.
Blinking green
during operation;
Charge the battery
Blinking green
battery is charging
Continuously green
battery is fully charged
* For reference only.
Following data for reference
DM15LEU/L-0.3/30
0.3
30
0.6
5
DM15LEU/L
A-00
-1-
-2-
Features
Built-in Receiver
Jog & Tilt
Built-in Lithium Battery
Scan and Program
Solar Charging
Switch Direction
Stall Protection
Program Button
Reset to Factory Mode
Status Feedback
Electronic Limit
Preferred Stop Position
Speed Regulation
Scene Control
Memorized Setting
Instruction
SAFETY NOTE
1, This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
2, Children shall not play with the appliance.
3, Cleaning and user maintenance shall not be made by
children without supervision.
4, If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5, WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6, The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or less
than 70 dB(A), e.g. by writing LpA
≤
70 dB(A).
7, The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8, The type of driven part the drive is intended for.
9, WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10, Do not allow children to play with fixed controls. Keep
remote controls away from children.
11, Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary.
12, Watch the moving shutter and keep people away until
he shutter is completely closed.
13, WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14, Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation.
Fields of Application
The motor is suitable for motorization of roller blinds.
Specifications
Working Temperature: -10
℃
~ +50
℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model
Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Current
(A)
Rated Power
(W)
Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Motor Installation
Drive tube
Drive tube
Step 1 Cut drive tube to required length.
Step 3 Mount correct crown & drive adapter on
the motor. Make sure drive adapter fits firmly and
crown rotates freely.
Step 4 Align the notches on the crown and drive
adapter with the drive tube, slide and fit the motor
into drive tube. Mount idler and bracket on both
ends.
Step 2 Ensure tube edge is clean and burr-free.
Bracket
Bracket
②
Drive Adapter
①
Crown
③
Circlip
Charging Instructions
Micro-USB charging: 5V
Micro-USB Port
Rechargeable Battery
This motor has a 8V built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) , or charging
with 5V solar panel.
During operation, motor will stop running when the voltage is lower than 6.5V and it will resume again when
the voltage is greater than 6.8V.
When the motor is running continuously when the voltage is lower than 7.2v, the red light will flash for 10 times
for low pressure alarm.
Blinking red
during operation;
Charge the battery
Blinking red;
battery is charging
Continuously red;
battery is fully charged
Solar (PV) Panel: 5V
Rechargeable Battery
2
