INSTALLATION TIPS
1. Use overall shielded audio cable only. West Penn 452, Belden 8451 or equivalent.
UNSHIELDED CABLE IS NOT SATISFACTORY FOR SOUND SYSTEMS.
2. When used in cashier’s booth, microphone should be installed closer to the customer rather than the
cash register, as the drawer sound may dominate the recording. It should be installed closest to the
area that needs to be monitored and documented.
3. Avoid installing microphone near air vents, air conditioner, fans and other equipment that generate
high sound and air pressure.
4. If using a VCR, it may have both intermittent and constant speed playback. See VCR’s manual on
how to select constant speed.
5. The APR-1 and microphone should have a barrier or solid wall between them in order to avoid audio
feedback, especially when they are in close proximity to each other up to 25’ (7.6 m).
7. Press “REC” on the recording device and record live audio for several minutes.
8. Press
Push for Playback Switch[7]
to “ON” position.
Playback Indicator LED[4]
will illuminate yellow.
9. Press “PLAY” on the DVR/VCR to playback recorded audio from the APR-1.
10. Press
Mute Switch[6]
to mute audio heard on the speaker.
Mute Indicator LED[3]
will light and no audio can be
heard on the speaker on both live and playback audio. When
Mute Switch[6]
is ON
Playback Indicator LED[4]
will
not light even when the
Push for Playback Switch[7]
is pushed in and the audio is muted.
4. Plug headphone into the
Headphone Jack[8]. Speaker[9]
output is muted and sound is transmitted through the
headphone.
5. Using the dual RCA cable (supplied), connect DVR/VCR’s AUDIO OUT jack to APR-1’s
AUDIO IN Jack[11]
.
6. Connect DVR/VCR’s AUDIO IN jack to APR-1’s
AUDIO OUT Jack[12]
.
WIRING CONNECTIONS AND TEST
Both the Verifact E Microphone and APR-1 Audio Base Station contain a 3-pin terminal block marked A, B, C.
A = 12Vdc Power
Red Wire
B = Audio
Black Wire
C = Ground
Bare Wire
1. Starting with the microphone, connect
RED
wire to Pin A,
BLACK
wire to Pin B and
BARE
wire to Pin . Connect
other end of cable to Terminal Block on back panel of APR-1 Base Station matching
RED
wire to Pin A,
BLACK
wire
to Pin B and
BARE
wire to Pin C. Refer to drawing on page 4.
2. Plug AD-1 power supply (AC Adapter) into the
Power Jack[10]
located on back panel of APR-1 first. Then connect 2-
prong block into standard 110/120 AC wall receptacle or power strip.
3. Turn “ON” power to APR-1 by rotating the
Power-Volume Knob[1]
clockwise. The green
Power Indicator[2]
LED
will illuminate. Adjust volume of audio by rotating the knob either clockwise to increase or counterclockwise to
decrease. Locate microphone so as not to create feedback with the APR-1. The further the microphone is from the
APR-1 the less feedback it generates. System works best if there is an acoustical barrier between the microphone
and the
APR-1, such as a wall or room divider. If there is no wall or barrier, microphone should be mounted at least 25 ft.
from the APR-1 Base Station.
2 Conductor shielded cable, 22 gauge
with a 24 gauge drain wire.
West Penn 452 or equivalent
INSTALLATION AND OPERATING INSTRUCTIONS
Page 5 of 8
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406
TEL (818) 994-6498
FAX
994-6458
website: www.louroe.com e-mail: [email protected]
(818)
®
ASK4_101E_inst 2/15
®
Verifact E microphone is designed for sufrace mounting to a wall or a pole. The top and back side of the Bell Box has
opening for conduit connections. As a finished unit, the unit is classified as weather resistant. Sealing around the face
plate and conduit connection is required.
