Louroe Electronics AP-2 Installation And Operating Instructions Manual Download Page 2

[6] -  Filter Switch

Normally used when playing back audio from a Time Lapse 
recorder.  This function is no longer available on this product

.

[7] -   DVR/VCR-IN Switch

Press to connect DVR/VCR into the unit.  Depressing switch 

bypasses the DVR/VCR even if it is connected physically to the 
back of the unit.  This eliminates the need to disconnect the 
DVR/VCR when not in use.

[8] -  Power-Volume Control Knob

Rotating knob clockwise turns on power to the unit, as indicated 

by the Filter-OUT Indicator

[2]. 

Rotating further clockwise 

increases the volume of the monitored audio produced through 
the Monitor Speaker

[10]

.

[9] -  Headphone Jack (3.5mm stereo)

Used for private listening.  Any monaural headset with 8 to 600

  

impedance maybe used.  Mutes the speaker output when in use.

   

DESCRIPTION AND FUNCTION OF PARTS

[1] -  Zone Selector Switches

Selects zone for monitoring.  Press switch of desired zone to 

listen to live audio.  Pressing more that one switch is possible 
when it is necessary to monitor more than one zone at a time, 
but audio may be difficult to understand if there is audio activity 
at several zones.

[2] - Filter-OUT Indicator

Lights (green) when audio filter is not in use.  Indicates power is 

“ON”.

[3] -  Filter-IN Indicator

Lights (red) when Filter Switch

[6]

 is pushed in to “ON” position.

[4] -  DVR/VCR-IN Indicator

Lights (yellow) when DVR/VCR switch

[7] 

is pushed in to “ON”.

[5] -  Overload Indicator

Lights (red) when a short or overcurrent in the power supply 

occurs.   If this occurs, turn OFF the Power-Volume Knob

[8] 

and 

check wiring connections (see troubleshooting, pg7).

Fig. 1 Front of AP-8

EIGHT ZONE A

UDIO SURVEILL

ANCE

MADE IN US

A

PHON

ES

1

2

3

4

5

6

7

8

ZONE

S

AP

-8

OFF

MAX

POWE

R-VOL

UME

VCR I

N

FILTE

R

PRES

S

PLAYB

ACK

FOR

OUT
IN

OVER

LOAD

3

4

5

6

1

2

7

8

9

Fig. 1 Front view of AP-8

AP-2 and AP-4 have the
same features except
for the number of Zones 

    

   

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 8

LOUROE  ELECTRONICS    6 9 5 5   VA L J E A N   AVENUE,  VAN  NUYS,  CA  91406

TEL  (818)  994-6498

FAX 

994-6458

website: www.louroe.com                          e-mail: [email protected]

   

   

(818)

®

ap_2_4_8_inst_5/11

Summary of Contents for AP-2









Reviews: