Part Number: A702T0002A
Version: 6
Exige V6 Cup Car
Supplementary Manual
- 14 -
NEVER STRAP MORE THAN ONE PERSON IN PLACE WITH EACH HARNESS BELT.
NEVER USE THE HARNESS BELT SYSTEM FOR PERSONS WHO WEIGH LESS THAN 40 KG (88 LBS) OR
THOSE WHO ARE LESS THAN 150 CM (4‘11“) TALL, REGARDLESS OF AGE.
NEVER USE THE LAP BELT PORTION OF THE HARNESS BELT WITHOUT THE SHOULDER BELTS.
ALL STRAPS MUST PERMANENTLY RUN THROUGH THE SLOTS OF THE BUCKET SEAT.
ALWAYS MAKE SURE THAT NO STRAP IS TWISTED WHEN WORN.
ALWAYS WEAR THE LAP BELT PORTION OF THE HARNESS SYSTEM LOW AND TIGHT ACROSS THE
PELVIS.
PRESSURE OF SHOULDER BELTS ON YOUR SHOULDER AND CHEST MUST BE EQUAL.
NEVER WEAR THE BELTS OVER HEAVY CLOTHING AS IT CAN INTERFERE WITH PROPER
POSITIONING AND ADJUSTMENT OF THE BELTS, REDUCING THE OVERALL EFFECTIVENESS OF THE
SYSTEM.
NEVER WEAR THE BELTS OVER RIGID OR BREAKABLE OBJECTS IN OR ON YOUR CLOTHING, SUCH
AS EYE GLASSES, PENS, JEWELRY, KEYS ETC AS THESE MAY CAUSE INJURY.
NEVER ALLOW STRAPS TO RUB AGAINST SHARP OBJECTS.
NEVER ALLOW THE BELTS TO BE DAMAGED BY BECOMING CAUGHT IN DOOR OR SEAT HARDWARE.
INSPECTION
INSPECT THE HARNESS BELT THOROUGHLY FOR DAMAGE BEFORE EACH USE.
MAKE SURE THAT THE INSPECTION OF THE BELT IS INCLUDED WITH REGULAR CHECKUPS OF THE
CAR AND ITS EQUIPMENT.
REGULARLY CHECK CORRECT TORQUE OF BOLTS.
CHECK FOR EXPIRATION DATE OF THE RACING HARNESS AS IT APPLIES TO THE REGULATION OF
YOUR SANCTIONING BODY AND/OR THE FIA, SFI OR NASCAR TAG, PRIOR TO EACH USE.
CLEANING AND MAINTENANCE
TO CLEAN THE HARNESS BELT, USE ONLY MILD SOAP AND WARM WATER.
NEVER USE SOLVENTS OR OTHER CLEANING SOLUTIONS, THEY CAN WEAKEN THE WEBBING OR
STITCH PATTERN.
NEVER USE CHEMICAL SOLVENTS OR CLEANING SOLUTIONS TO CLEAN THE ROTARY BUCKLE. THE
HIGH IMPACT RESISTANT POLYCARBONATE [PC] MATERIAL IS SENSITIVE TO ANY KIND OF
HYDROCARBONS, ALSO TO SPRAY CLEANERS CONTAINING HYDROCARBONS.
DO NOT DRY THE BELT IN THE SUN OR NEAR A RADIATOR, IN A CLOTHES DRYER OR WITH A HAIR
DRYER OR WITH ANY OTHER MECHANICAL OR ELECTRICAL HEATING DEVICE. HEATING WEBBING
MAY MAKE THE MATERIAL SHRINK AND THE PRECISELY DESIGNED ELONGATION RATE WILL BE
CHANGED.
ALWAYS ALLOW A CLEANED BELT TO AIR DRY NATURALLY.
ALWAYS HAVE DAMAGED SUB-ASSEMBLIES OF THE HARNESS BELT REPLACED BEFORE USING THE
HARNESS BELT AGAIN.
NEVER MODIFY, DISASSEMBLE OR REPAIR THE BELT BY YOURSELF.
ACCIDENT
ANY HARNESS BELT WHICH WAS USED DURING AN ACCIDENT IS UNFIT FOR FURTHER USE AND
MUST BE REPLACED.
NEVER CONTINUE TO USE A HARNESS BELT, WHICH WAS IN USE DURING AN ACCIDENT. REPLACE IT
IMMEDIATELY.
IN SCHROTH PROFI ASM ® MODELS, A PARTLY OR FULLY RIPPED OPEN SCHROTH ASM ® SYSTEM
INDICATES THE NEED OF IMMEDIATE REPLACEMENT OF THE RACING HARNESS.
FIA AND OTHER SANCTIONING BODIES REQUIRE THAT INSPECTORS CUT THE RACING HARNESS, OR CUT
THE LABELS OFF THE RACING HARNESS, AFTER AN ACCIDENT. ALWAYS INSPECT ALL ANCHORAGES FOR
DAMAGE SUCH AS DEFORMATIONS OR CRACKS, AFTER AN ACCIDENT. STRICTLY FOLLOW THE
RECOMMENDATIONS OF THE VEHICLE OR ROLL CAGE MANUFACTURER IF A REPAIR SHOULD BE
NECESSARY.