background image

SAFETY WARNINGS AND PRECAUTIONS 

PLEASE READ AND UNDERSTAND THE FOLLOWING SAFETY HIGHLIGHTS. 

BE  SURE  THAT  ALL  INSTALLATION,  OPERATION,  MAINTENANCE  AND 

REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS. ARC 

AND TIG WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM 

POSSIBLE  SERIOUS  INJURY  OR  DEATH.  KEEP  CHILDREN  AWAY.  PACEMAKER 

WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.   

WHEN  USING  THE  WELDER, ALL  BASIC  SAFETY PRECAUTIONS  SHOULD  ALWAYS  BE 
FOLLOWED  TO  REDUCE  THE  RISK  OF  PERSONAL  INJURY  AND  DAMAGE  TO 
EQUIPMENT.   

DRY WORKING PLACE. DO NOT WELD IN PLACES WITH HIGH HUMIDITY. 
FOR THE POWER EXTENSION CORD, PLEASE MAKE SURE THE WIRE GAUGE IS MORE 
THAN  11  GAUGE  AT  220VAC  AND  13  GAUGE  AT  110VAC.  USING  A  NON-METALLIC 
CHAIR PLACED ON A RUBBER MAT WHILE WELDING IS RECOMMENDED. USE 20 AMPS 
CIRCUIT BREAKER FOR 110VAC AND 30 AMPS CIRCUIT BREAKER FOR 220VAC. DO NOT 
USE TRIPLE PHASE, INSTEAD USE SINGLE PHASE POWER. 

READ ALL INSTRUCTIONS BEFORE USING THIS WELDER. 

Keep work area clean. 

Cluttered areas invite injuries. 

Observe work area conditions.

 Do not use machines or power tools in damp or wet locations. 

Do  not  expose  to  rain.  Keep  work  area  well-lighted.  Do  not  use  electrically  powered  tools  in  the 
presence of flammable gases or liquids. 

Keep  children  away. 

Children  must  be  never  be  allowed  in  the  work  area.  Do  not  let  them 

handle machines, tools or extension cords. 

Store idle equipment

. When not in use, tools must be stored in a dry location to inhibit rust. 

Always lock up tools and keep them out of the reach of children.   

Do not force tool

. It will do the job better and safer at the rate for which it was intended. Do not 

use inappropriate attachments in an attempt to exceed the tool capacity. 

Use the right tools for the job.

 Do not attempt to force a small tool or attachment to do the work 

of a larger industrial tool. There are certain applications for which this welder was designed. Do not 
modify this welder and do not use this welder for any other purposes for which it was not intended.   

Dress properly. 

Do not wear loose clothing or jewelry as they can be caught in moving parts. 

Protective,  flame  retardant,  electrically  non-conductive  clothing  and  non-skid  footwear  are 
recommended when working. Wear restrictive hair covering to contain long hair. 

Use eye and ear protection.

 Always wear 

ANSI

 approved, arc shaded, impact safety face shield 

(welding helmet). Always use a full-face shield when welding. Always wear 

ANSI

 approved eyewear 

under face shield and while in the workplace. Wear a NIOSH approved dust mask or respirator when 
working around metal, chemical dusts, fumes and mists. 

Do not over reach.

 Keep proper footing and balance at all times. Do not reach over or across 

running machines 

Summary of Contents for TIG140




















Reviews: